Hearth and Home Technologies CB4842MIR Bedienungsanleitung

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 1 Model(s): CB4236MIR CB4842MIR B-V ent Gas Appliance Owner ’ s Manual Installation and Operation DO NOT DISCARD THIS MANUAL NOTICE • Leave this manual with party responsible for use and operation. Installation and service of this appliance should be performed by quali fi ed pe[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: _____________[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation w[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 4  = Contains updated information. 14 Appliance Setup A. Remove Glass Assembly 29 B. Remove the Shipping Materials 29 C. Clean the Appliance 29 D. Accessories 29 E. Install the Refractory 29 F . Place the Lava Rock & V ermiculite 29 G. Place the Rockwool 29 H. Install the Log[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 5 B. W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 6 B. W arranty (continued) This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on a[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as de fi ned by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested an[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 8 Grate (not shown) Section 14.H. Mantel Section 5.D. Hearth (not required) Clear Space Section 2.D. W all Switch for Fan Section 12.F . Outside Air Kit (behind panel) Section 9.A. Fixed Glass Assembly Section14.I. Remote Control 2 2 Operat ing Instruc tions Figure 2.1 Fireplace Com[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 9 Clear Space 3 ft (0.91 m) in front of appliance D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High tempera- tures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or heart[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 10 J. Lighting Instructions (IPI) • For normal use, activate/deactivate your fi replace with the wall switch or remote control. • The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when [...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 1 1 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.I. • Clean fi xed glass assembly . See Section 3. • Replace[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 12 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed: Protective gloves, glas s cl ean er , d rop clot h and a stabl e work sur face. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abras[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 13 Burner Ignition and Operation Frequency: Annually By: Quali fi ed Service T echnician T ools needed: Protective gloves, vacuum cleaner , whisk broom, fl ashlight , voltmeter , indexed drill bit set, an d a manom- eter . • V erify burner is properly secured and aligned with pi[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 14 Noncombustible roof flashing maintains minimum clearance around pipe Ceiling Firestop on floor of attic Listed B-V ent Pipe Framing/Header (SECTION 5) Gas Line (SECTION 1 1) Framing Headed off in Ceiling Joists (SECTION 8) Mantel & Mantel Leg (SECTION 13) Surround Hearth Exte[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 15 B. Design and Installation Considerations Heatilator B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room. Installation MUST comply with local, regional, state and national codes[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 16 Recommended Location Marginal Location Location Not Recommended Recommended Location Multi-level Roofs Windward Leeward Location Not Recommended Figure 4.2 E. Negative Pressure W ARNING! Asphyxiation Risk! Negative pressure can cause spillage of combustion fumes and soot. Firepla[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 17 A A A C E B B 1/2 in. (13 mm) C 48 in. (1219 mm) max. Drywall D 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls, Figures 5.1 and 5.2. NOTICE: Illustrations re fl [...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 18 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase. NOTICE: T reatment of ceiling fi restops and wall shield fi restops and construc[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 19 0 in. C B A Note: All pipe clearance specifications are per vent manufacturer's installation instructions. 0 (Clearance to Standoffs) 30 in. (762 mm) clearance to ceiling 1/2 in. (13 mm) 1/2 in. (13 mm) Drywall 0 in. Per V ent Manufacturer ’ s Specifications Combustible fl[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 20 1 in. (25 mm) min. to perpendicular wall A 3-1/2 in. (89 mm) min. from fireplace opening to perpendicular wall B Mantel Leg or Perpendicular W all T op of Appliance Drywall A B Measured from top of hood (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 5-1/2 6-1/4 7 7-3/4 8-[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 21 A. V ent T ermination Minimum Clearances A Gas T ermination W ood or Fuel Oil T ermination B 6 in. (152 mm) min. 20 in. (508 mm) min. B-V ent Gas, Wood or Fuel Oil T ermination 8 ft (2.44 m) (minimum) to Perpendicular W all (BV only) 18 in. (457 mm) A Gas T ermination B T erminat[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 22 Minimum clearances are per vent manufacturer's specifications Metal plumber's strap secured to framing V ent supports are per vent manufacturer's specifications 12 ft (3.66 m) min. 60 ft (18.29 m) max. 45° Elbow 90° Elbow Offsets exceeding 45° adapt horizontal l[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 23 A. Pipe Clearances to Combustibles V ent clearances are per vent manufacturer ’s speci fi ca- tions. The vent MUST be Listed B-V ent pipe. W ARNING! Risk of Fire! MAINT AIN AIR space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi resto[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 24 The diagram shows how to properly position, level, and secure the appliance (see Figure 9.2). Nailing tabs are provided to secure the appliance to the framing members. • Bend out nailing tabs on each side. • Place the appliance into position. • Keep nailing tabs fl ush wit[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 25 T abs 1 0 10 Installing V ent Pipe A. Assembly of V ent Sections This B-V ent appliance requires 5 in. B-vent double-wall pipe. Follow the pipe manufacturer ’ s installation guide- lines when installing the unit. This will ensure proper operation and prevent safety hazards. W A[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 26 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. C. Gas Connection • Refer to Reference Section 16.A. for [...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 27 B. Intelli fi re Ignition System Wiring • Wire the appliance junction box to 1 10 V AC for proper operation of the appliance. W ARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safet[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 28 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan, see Figure 12.3: • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to the applian[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 29 Measured from top of hood (in inches) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 5-1/2 6-1/4 7 7-3/4 8-1/2 9-1/4 10 10-3/4 11 - 1 / 2 12-1/4 13 13-3/4 14-1/2 15-1/4 16 30 in. minimum to ceiling 1 in. (25 mm) min. to perpendicular wall A 3-1/2 in. (89 mm) min. from fireplace openi[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 30 A. Remove Glass Assembly See Section J. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . D. Acce[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 31 Latches (both bottom and top) Glass Assembly Figure 14.8 Fixed Glass Assembly H. Install the Log Assembly • Base logs have been permanently mounted on the grate assembly and should not be moved. See Figure 14.5. Figure 14.7 Placing Right T op Log Figure 14.6 Placing Left T op L[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 32 J. Install T rim • Install optional trim kits and/or surrounds using the instructions included with the accessory . • Use non-combustible materials to cover the gap between the sheet rock and the appliance (if desired). • Do not obstruct or modify the air inlet/outlet grill[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 33 L. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shut- ter for longer vertical runs. • It takes 16 full turns of the shutter ad[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 34 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service technician in the diagnosis of a problem and t[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 35 A. Intelli fi re Ignition System (continued) 4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occurred.) A. A shorted or loose connection in fl ame se[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 36 1 6 16 R eference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions 38-1/4 in. (972 mm) B 1-1/2 in. (38 mm) 3 in. (76 mm) 6-1/2 in[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 37 B. Service Parts List Service Parts 08/08 Service Parts Diagram Caliber Clean Face Assembly CB4236MIR Part number list on following page. Log Set Assembly 6 3 1 2 4 5 7 8 9 10 11 21 22 23 12 13 14 15 16 17 18 19 20 Beginning Manufacturing Date: Jan 2007 Ending Manufacturing Date:[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 38 B. Service Parts List (continued) Service Parts 08/08 Service Parts Diagram Caliber Clean Face CB4842MIR Part number list on following page. Log Set Assembly 6 3 1 2 4 5 Beginning Manufacturing Date: Jan 2007 Ending Manufacturing Date: Active 7 8 9 10 11 21 22 23 12 13 14 15 16 1[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 39 B. Service Parts List (continued) Service Parts 08/08 IMPORT ANT : THIS IS DA TED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer [...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 40 C. Optional Components Contact your dealer for a complete listing of optional components. Refractory Kit WTBC36DB - For 36 in. BV WTBC42DB - For 42 in. BV Arts & Crafts Faux Front FFCAC Modernist Faux Front FFCM Jamestown Faux Front FFCJ[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 41 Model # Description FFCM36-B Modernist-style black decorative faux front FFCM36PT Modernist-style pewter decorative faux front FFCM36BN Modernist-style brushed nickel decorative faux front FFCAC36-B Arts & Crafts-style black decorative faux front FFCAC36PT Arts & Crafts-s[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 42 This page intentionally left blank.[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 43 This page intentionally left blank.[...]

Heatilator • Caliber Mesh BV Series • 4040-848 Rev G • 10/08 44 D. Contact Information Please contact your Heatilator dealer with any questions or concerns. For the location of your nearest Heatilator dealer , please visit www .heatilator .com. - NOTES - ________________________________________________________________________________ ________[...]