Extron electronic MGP 462 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Extron electronic MGP 462 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Extron electronic MGP 462, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Extron electronic MGP 462 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Extron electronic MGP 462. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Extron electronic MGP 462 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Extron electronic MGP 462
- Den Namen des Produzenten und das Produktionsjahr des Geräts Extron electronic MGP 462
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Extron electronic MGP 462
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Extron electronic MGP 462 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Extron electronic MGP 462 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Extron electronic finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Extron electronic MGP 462 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Extron electronic MGP 462, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Extron electronic MGP 462 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    MGP 462D Multi-Graphic Processor 68-840-01 Rev. C 08 06 MGP 462[...]

  • Seite 2

    Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read In[...]

  • Seite 3

    QS-1 MGP 462 • Quick Start Quick Start — MGP 462, cont’d R /R-Y G /Y B /B-Y HV S R /R-Y G /Y B /B-Y HV S R /R-Y G /Y B /B-Y HV S R /R-Y G /Y B /B-Y HV S RGBHV RGBS RGsB HDTV Component Video BNC output connectors Step 5 Plug the MGP 462, input devices, and output devices into a grounded AC source, and power on the input and output devices. MGP[...]

  • Seite 4

    Quick Start — MGP 462, cont’d MGP 462 • Quick Start QS-2 Quick Start — MGP 462, cont’d Main Menu flow c . Press the W indow/Image Size button once , and turn the Adjust knobs to the right until they stop. The window size setting displays the same r esolution as the output. d . Repeat steps a through c for the remaining window . W ith both[...]

  • Seite 5

    QS-3 MGP 462 • Quick Start Quick Start — MGP 462, cont’d Step 8 For each input, size and position the image within both window 1 and window 2. a . Press one of the six input buttons in the top row (for window 1) or the bottom row (for window 2). b . Press the window button that corresponds with the input button that you pressed (e.g., if you [...]

  • Seite 6

    Quick Start — MGP 462, cont’d MGP 462 • Quick Start QS-4 Quick Start — MGP 462, cont’d[...]

  • Seite 7

    i MGP 462 • Table of Contents T able of Contents Chapter 1 • Introduction ....................................................................................................... 1-1 About This Manual ............................................................................................................. 1-2 About the MGP 462/462D .........[...]

  • Seite 8

    ii MGP 462 • Table of Contents T able of Contents, cont’d Window T ext Configuration menu ................................................................................. 3-14 Window T ext Position submenu ............................................................................... 3-14 Window T ext Size submenu ............................[...]

  • Seite 9

    iii MGP 462 • Table of Contents Chapter 5 • Ethernet Configuration and Control ................................................. 5-1 Accessing the Web pages ................................................................................................ 5-2 V iewing System Status .................................................................[...]

  • Seite 10

    iv MGP 462 • Table of Contents T able of Contents, cont’d Window Presets screen .................................................................................................... 5-18 Naming a window preset ......................................................................................... 5-19 Saving (creating) a window preset ........[...]

  • Seite 11

    MGP 462 Multi-Graphic Pr ocessor 1 Chapter One Intr oduction About This Manual About the MGP 462/462D Features Application Diagram[...]

  • Seite 12

    Introduction, cont’d MGP 462 • Introduction 1-2 Intr oduction About This Manual This manual discusses how to install, operate, and configure the Extron MGP 462 multi-graphic processor . Throughout this manual, the terms “MGP ,” “multi-graphic pr ocessor ,” and “processor” are used inter changeably to refer to the same product. About[...]

  • Seite 13

    1-3 MGP 462 • Introduction A similar process, 2:2 film detection, is used for P AL film-source video. Background image capture, save, and recall — Background Captur e enables you to capture and save the image currently on the output scr een. Y ou can then recall the captured image and display it as a backgr ound later . Auto Image ™ — Auto [...]

  • Seite 14

    Introduction, cont’d MGP 462 • Introduction 1-4[...]

  • Seite 15

    MGP 462 Multi-Graphic Pr ocessor 2 Chapter T wo Installation Mounting the MGP 462 Connecting the MGP 462 Installing or Replacing Button Labels Cabling[...]

  • Seite 16

    Installation, cont’d MGP 462 • Installation 2-2 Installation Mounting the MGP 462 T abletop use Four self-adhesive rubber feet are included with the MGP 462. For tabletop use, attach one foot to each corner of the bottom side of the unit and place the MGP in the desired location. Rack mounting The MGP can optionally be mounted in a rack with th[...]

  • Seite 17

    2-3 MGP 462 • Installation Connecting the MGP 462 The MGP 462 pr ocessor can be connected to as many as six input devices simultaneously , and two output devices (displaying the same image). Follow the steps below to set up the MGP 462 har dware. 1 Disconnect power to the MGP , and turn off all other devices that will be connected. 2 If the MGP 4[...]

  • Seite 18

    Installation, cont’d MGP 462 • Installation 2-4 2 1 TEXT S ep a r a te the two- piece b u tton a t the corner. Pry the two piece s a p a rt. Diff us er Pl u nger B as e B u tton L a bel Cle a r Len s Notch Replacing a button label 5 . Lift out the transparent square label that you want to replace. Y ou may need to use the small screwdriver to g[...]

  • Seite 19

    2-5 MGP 462 • Installation Input connectors 1 Inputs 1, 2, 3, and 4 — Plug RGB, component video, S-video, or composite video sources into these BNC connectors as shown in the diagram below . RGBHV Video RGsB or Component Video S-Video Composite Video RGBS or RGBcvS Video H /HV V R /R-Y G /Y VID B /C B-Y H/ HV V R /R-Y G /Y VID B /C B-Y H/HV V R[...]

  • Seite 20

    Installation, cont’d MGP 462 • Installation 2-6 Clip Down 1 1&2 3 &6 4&5 7& 8 2 3 4567 8 12 3 4567 8 RJ-45 Connector Tw i s ted Pai r s S traight-through Cab le (for connection to a s witch, h u b, or ro u ter) End 1 End 2 Pin Wire Color Pin Wire Color 1 white-or a nge 1 white-or a nge 2 or a nge 2 or a nge 3 white-green 3 white[...]

  • Seite 21

    2-7 MGP 462 • Installation Remote control connector 7 RS-232/422 connector — Plug a computer or other RS-232 or RS-422 host device into this female D-sub connector . W ire the connector as shown in the tables below . For more information on controlling the MGP 462 remotely , see chapter 4, Software Configuration and Contr ol . Pin assignments f[...]

  • Seite 22

    Installation, cont’d MGP 462 • Installation 2-8[...]

  • Seite 23

    MGP 462 Multi-Graphic Pr ocessor 3 Chapter Thr ee Operation Front Panel Features Power -up and Default Cycle Input Selection Window Selection Buttons Menus, Configuration, and Adjustments Picture Controls Memory Presets Additional Functions[...]

  • Seite 24

    Operation, cont’d MGP 462 • Operation 3-2 Operation The MGP 462 can be set up and operated by using: • The front panel contr ols • A computer , a touch screen panel, or any other device that can send and receive serial communications thr ough the RS-232/422 port. Settings can be adjusted through the host computer using Extron’s Simple Ins[...]

  • Seite 25

    3-3 MGP 462 • Operation 8 Adjust knobs — T urn these knobs to adjust picture controls and to scr oll thr ough pr eset memory slots and submenu options. See Menus, Configuration, and Adjustments , later in this chapter , for more information. Power -up and Default Cycle When you first plug the MGP 462 into a power sour ce, the LCD screen display[...]

  • Seite 26

    Operation, cont’d MGP 462 • Operation 3-4 Window Selection Buttons The MGP 462 front panel contains two W indow buttons, located to the right of the two input 6 buttons. Use these buttons with the picture control buttons to select the window to be adjusted. When you select a picture control, it af fects the selected window . (Refer to Picture C[...]

  • Seite 27

    3-5 MGP 462 • Operation Pow e r on Multi-Graphic Proce ss or Input Configuration 2 s ec. MENU MENU Output Configuration MENU 20 s ec. Window Configuration MENU 20 s ec. 20 s ec. Default Cycle Extron MGP 462 V2.01 2 s ec. Adv anced Configuration 20 s ec. MENU MENU NEXT Exit Menu Pre ss Next Window T ext Configuration MENU 20 s ec. Backgr ound Capt[...]

  • Seite 28

    Operation, cont’d MGP 462 • Operation 3-6 Auto Image menu The Auto Image menu causes the MGP 462 to perform an automatic image adjustment to the selected window . Auto Image measures where the active ar ea starts and stops, and adjusts input sampling accordingly . When Auto Image is performed, the processor measures the sync fr equencies of the[...]

  • Seite 29

    3-7 MGP 462 • Operation The following diagram shows the submenus of the Input Configuration menu and the adjustments that can be made from them. Input Configuration menu flow The following table lists the signal types available for each input. Input video signal types Signal T ype Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 RGB*** X* X* X* X [...]

  • Seite 30

    Operation, cont’d MGP 462 • Operation 3-8 Input configuration submenu adjustments The table below shows which Adjust knob to use to make the selections and adjustments that are accessed through the Input Configuration submenus. Input Co nfigurat io n subme nu H ori zo ntal k no b ad ju stm e nt V ert ical kn ob a djustmen t Vi d e o t y p e The[...]

  • Seite 31

    3-9 MGP 462 • Operation Output Configuration menu The Output Configuration menu allows you to set the output resolution, refr esh rate, output type, and sync polarity . The following flow diagram shows the submenus of the Output Configuration menu, and the adjustments that can be made fr om them. The menus time out and return to the default cycle[...]

  • Seite 32

    Operation, cont’d MGP 462 • Operation 3-10 Resolution and Refresh Rate submenu Rotate the horizontal Adjust ( [ ) knob while in this submenu to select fr om one of the available resolutions. Rotate the vertical Adjust ( { ) knob while in this submenu to select one of the available refresh rates. The available r esolution and refr esh rates are [...]

  • Seite 33

    3-11 MGP 462 • Operation Output T ype submenu Rotate either the horizontal Adjust ( ) or the vertical Adjust ( ) knob to select the output signal type requir ed by the display device. A vailable signal types are RGBHV , RGsB, YUV bi-level and YUV tri-level. The default is RGBHV . Combined H and V Sync (S) is available on the “S” BNC connector[...]

  • Seite 34

    Operation, cont’d MGP 462 • Operation 3-12 Window 1 Border and Window 2 Bor der submenus Use these submenus to select border colors for the two windows. A vailable options are Red, Green, Blue, White, Magenta, Cyan, Y ellow , and Black . Y ou can also select None (no bor der), which is the default setting. Window Effect submenu Use this submenu[...]

  • Seite 35

    3-13 MGP 462 • Operation Square wipe — A squar e wipe causes the new window to appear to unroll over the other one in one of two ways: • In from the top, bottom, right, and left edges to the center of the window • Out from the center to the four edges of the window This ef fect cr eates a squar e shaped transition. A square wipe can have a [...]

  • Seite 36

    Operation, cont’d MGP 462 • Operation 3-14 Window T ext Configuration menu This menu enables you to add a text box, containing up to 16 characters, to each window . The submenus allow you to enter the text for the label; select an on-screen position where the text will appear; and specify colors for the text, the text box backgr ound, and the b[...]

  • Seite 37

    3-15 MGP 462 • Operation WIndows 1 and 2 T ext Backgr ound submenus The W indows 1 and 2 T ext Background submenus let you select a background color for the text box you place on window 1 or window 2. Rotate either the horizontal Adjust ( ) or the vertical Adjust ( ) knob to select one of the available background colors. Options ar e Red , Green [...]

  • Seite 38

    Operation, cont’d MGP 462 • Operation 3-16 Background Captur e menu The Background Capture menu allows you to captur e the image that is currently displayed on the output screen and save it as a bitmap (.bmp) file with one of 16 designated image names. Y ou can then recall the image and use it as a background. Background Capture also can be don[...]

  • Seite 39

    3-17 MGP 462 • Operation CA UTION The image that you save overwrites any existing image file with the same file name. 4 . Press the Detail button (the top button located at the immediate left of the LCD screen). The LCD screen displays the message “Saving Backgr ound Please W ait,” along with an incrementing number showing the per cent of the[...]

  • Seite 40

    Operation, cont’d MGP 462 • Operation 3-18 Background Color submenu Rotate either Adjust knob to select a background color for the output scr een. Options are None, Red, Green, Blue, White, Magenta, Cyan, Y ellow , Stored-Image, and User Defined . • None , the default setting, pr oduces a black backgr ound. • Stored-Image is the saved backg[...]

  • Seite 41

    3-19 MGP 462 • Operation 4x 3 4x 3 4x 3 4x 3 Color Bars ( 8 ) Crosshatch 16x12 Crosshatch 4x4 Gra yscale Ramp Alt Pixels Crop 4x 3 Side- b y-side Crop 1.7 8 Aspect Ratio 1. 8 5 Aspect Ratio 2. 3 5 Aspect Ratio 16x9 Side- b y-side Crop T est patterns available for the MGP 462 Serial Port Mode submenu Use the Serial Port Mode submenu to select eith[...]

  • Seite 42

    Operation, cont’d MGP 462 • Operation 3-20 Adjusting the picture controls Make image adjustments to an input using the pictur e contr ol buttons on the front panel. When you select a picture contr ol button, it lights with the same color (green or red) as the selected buttons for the window and input that it will adjust. When you select a contr[...]

  • Seite 43

    3-21 MGP 462 • Operation T o adjust the picture contr ols, follow these steps: 1 . Press the Input button for the input that you want to adjust, if it is not currently selected. 2 . Press the W indow 1 or 2 button to select the window you want to adjust. 3 . Press the button for the desired pictur e contr ol: W indow/Image Size (sizing), Bright/C[...]

  • Seite 44

    Operation, cont’d MGP 462 • Operation 3-22 4 . Press the Enter button to save the curr ent window setting in the preset location number you selected. The LCD screen shows a message indicating that the preset is being saved to the selected memory location, followed by a message that the preset has been saved. The following examples show a preset[...]

  • Seite 45

    3-23 MGP 462 • Operation 4 . Press the Enter button to r ecall the preset you selected. The LCD scr een shows a message indicating that the preset was r ecalled. The following example shows a message indicating that preset 1 was recalled. WINDOW PRESET #01 RECALLED If you want to exit this menu without recalling a preset, repeatedly pr ess the Pr[...]

  • Seite 46

    Operation, cont’d MGP 462 • Operation 3-24 Additional Functions Fr eeze mode The front panel Freeze buttons are the first buttons on the left. Pr ess these buttons to freeze the current image fr om the currently selected input in window 1 (top button) and/or window 2 (bottom button). When the Freeze button for a window is selected, it lights or[...]

  • Seite 47

    3-25 MGP 462 • Operation Re s et Mo d e Compari s on/ S ummary Mo d e A c tivation Re s ult Purpo s e/Note s 1 Hold dow n t he recessed Rese t b utt o n wh i le apply ing power t o t he unit . 3 Hold dow n t he Rese t b utt o n for abo ut 3 seco n ds, unti l t he Rese t L E D bl in ks o n ce. The n , w it h in 1 seco n d, press Rese t a g a in br[...]

  • Seite 48

    Operation, cont’d MGP 462 • Operation 3-26[...]

  • Seite 49

    MGP 462 Multi-Graphic Pr ocessor 4 Chapter Four Softwar e Configuration and Contr ol Setting Up RS-232/RS-422 Communication Using Simple Instruction Set (SIS ™ ) Commands Using the Windows ® -based Control Software Using the Button Label Generator[...]

  • Seite 50

    Software Configuration and Contr ol MGP 462 • Software Configuration and Control 4-2 Setting up RS-232/RS-422 Communication The MGP 462’s RS-232/422 port is used to connect the MGP to a host or external controlling device, such as a computer or control system, which can generate the pr oper command codes and recognize the pr ocessor ’s respon[...]

  • Seite 51

    4-3 MGP 462 • Software Configuration and Control Out nn In nn (wher e Out nn is the window number , and In nn is the input number). The MGP 462 sends this response when an input is switched. Error r esponses When the MGP 462 receives a valid SIS command, it executes the command and sends a response to the host device. If the MGP is unable to exec[...]

  • Seite 52

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-4 ASCII to HEX Con version T able • ASCII to hexadecimal character conversion table The command/r esponse tables list valid ASCII (for T elnet) command codes, th e corresponding URL encoded (for W eb browsers) command codes, th e MGP’s responses to th[...]

  • Seite 53

    4-5 MGP 462 • Software Configuration and Control X 20 = T ime in tens of milliseconds to wait between characters coming into a serial port before terminating the connection (min = 0, max = 32767, and default = 2 = 20 ms). The response is r eturned with leading zeros. In RS-232/422 commands, X1 7 and X 20 are optional. Commands using both X1 7 and[...]

  • Seite 54

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-6 X5 9 = T est pattern 0 = off 1 = color bars 2 = crosshatch 3 = 4 x 4 crosshatch 4 = grayscale 5 = crop 6 = ramp 7 = Alternating pixels 8 = side-by-side crop 9 = 4 x 3/16 x 9 film aspect ratio 1.78 10 = 4 x 3/16 x 9 film aspect ratio 1.85 1 1 = 4 x 3/16 [...]

  • Seite 55

    4-7 MGP 462 • Software Configuration and Control X6 7 = W indow transition effect type 1 = cut 2 = dissolve 3 = soft wipe up 4 = soft wipe down 5 = soft wipe right 6 = soft wipe left 7 = soft wipe center in 8 = soft wipe center out 9 = soft wipe square in 10 = soft wipe square out 1 1 = soft wipe curtain in 12 = soft wipe curtain out 13 = hard wi[...]

  • Seite 56

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-8 Command/response table for SIS commands Command ASCII Command Response Additional description (host to processor) (processor to host) Input selection Set input to window X5 5 * X5 7 ! Out X5 7 In X5 5 Set input source X5 5 to window X5 7 . Input video t[...]

  • Seite 57

    4-9 MGP 462 • Software Configuration and Control Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Tint Set tint to a specific value X5 7 * X6 2 T X5 7 T in X6 2 Select tint value X6 2 in window X5 7 . Incr ement tint value X5 7 + T X5 7 T in X6 2 Sele[...]

  • Seite 58

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-10 Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Horizontal shift (image) Set horizontal shift to a specific value 2 * X5 7 * X7 8 H X5 7 Ihp X7 8 Set the [...]

  • Seite 59

    4-11 MGP 462 • Software Configuration and Control Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) V ertical size (window) Set vertical size to a specific value 1 * X5 7 * X7 9 ; Wvs X7 9 Set the vertical sizing of window X5 7 to X7 9 . Incr ease vert[...]

  • Seite 60

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-12 Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Zoom mode (window) Zoom in 1 * X5 7 + { X5 7 Wzm Increase the size of window X5 7 while keeping the aspect[...]

  • Seite 61

    4-13 MGP 462 • Software Configuration and Control Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) V ertical start Set vertical start to a specific value * X6 8 ( Vst X5 5 * X6 8 Set the vertical location of first active pixel in the window displaying[...]

  • Seite 62

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-14 Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) T otal pixels, continued V iew total pixels setting X5 5 * 1 1# X7 4 Show the current total pixels setting[...]

  • Seite 63

    4-15 MGP 462 • Software Configuration and Control Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Executive mode Enable executive mode 1X Exe1 Lock front panel control; allow RS-232/422 adjustments only . Enable executive mode 2 2X Exe2 Lock all fron[...]

  • Seite 64

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-16 Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Special functions, continued T ext border color X5 7 * X ! * 14# X5 7 Txb X ! Set the color of the text bo[...]

  • Seite 65

    4-17 MGP 462 • Software Configuration and Control Command/response table for SIS commands (continued) Command ASCII Command Response Additional description (host to processor) (processor to host) Special functions, continued W indow bor der color X5 7 * X ! * 9# X5 7 Brd X ! Set the border color for window X5 7 to X ! : 0 = none (default) 1 = r e[...]

  • Seite 66

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-18 Backgr ound color , continued Set user -defined color levels X ! * X ! * X ! * 22# Ubk X ! * X ! * X ! Set the r ed, gr een, and blue values for the user -defined color . X ! = 0-255 level scale. Example: 50 * 100 * 150 * 22# Ubk 50 * 100 * 150 The r e[...]

  • Seite 67

    4-19 MGP 462 • Software Configuration and Control Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) Bi-directional serial data port, continued Configur e serial port parameters 24 Esc X1 * X2 5 , X2[...]

  • Seite 68

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-20 Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enc oded (Web) Response Additional description (host to processor) (host to processor) (processor to host) Ethernet data port Set current connection port timeou[...]

  • Seite 69

    4-21 MGP 462 • Software Configuration and Control Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Encoded (Web) Response Additional description (host to processor) (host to processor) (processor to host) Firmware version r equests, continued Query factory firmware version 3Q 3Q X1 1 (plus web ver .-desc[...]

  • Seite 70

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-22 Command/r esponse table for IP contr ol port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to pr ocessor) (host to pr ocessor) (processor to host) Information requests, continued Request model na[...]

  • Seite 71

    4-23 MGP 462 • Software Configuration and Control Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enc oded (W eb) Response Additional description (host to processor) (host to processor) Event control, continued Read string from event buffer memory 27 Esc X3 5 , X3 6 , X3 7 , X4 4 FE W X3 5 , X3 6 , X3 7[...]

  • Seite 72

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-24 Command/r esponse table for IP contr ol port commands (continued) Command ASCII (T elnet) URL Encoded (W eb) Response Additional description (host to pr ocessor) (host to pr ocessor) (pr ocessor to host) Mail server setup commands Set mail server IP , [...]

  • Seite 73

    4-25 MGP 462 • Software Configuration and Control Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) IP setup commands, continued Read time/date Esc CT WCT | X1 3 The Read format is day of week, DD m[...]

  • Seite 74

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-26 Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) IP setup commands, continued Read IP address 24 Esc [...]

  • Seite 75

    4-27 MGP 462 • Software Configuration and Control Command/r esponse table for IP contr ol port commands (continued) Command ASCII (T elnet) URL Encoded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) IP setup commands, continued Clear user password 24 Esc • CU W%20CU | Ipu • This clears the u[...]

  • Seite 76

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-28 Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) Remapping port designations, continued Reset Direct [...]

  • Seite 77

    4-29 MGP 462 • Software Configuration and Control Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enco ded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) File commands Read Direct Access port map Esc MD WMD | {port#} Get listing Esc DF WDF | (See below[...]

  • Seite 78

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-30 Command/response table for IP control port commands (continued) Command ASCII (T elnet) URL Enc oded (W eb) Response Additional description (host to processor) (host to processor) (processor to host) Directory commands Change/create directory Esc {path[...]

  • Seite 79

    4-31 MGP 462 • Software Configuration and Control Using the Windows ® -based Contr ol Software The MGP 462 W indows-based control softwar e program pr ovides a convenient way to configure the inputs, output, windows, and images in each window . It also lets you save and recall input and window presets, and perform nearly all the other functions [...]

  • Seite 80

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-32 Link to the installation software on the MGP 462 CD 3 . On the File Download window that appears, click Run to begin installing the program. File Download window If you want to save the installation file (MGP462Setupv2_ n .exe) to your desktop, click S[...]

  • Seite 81

    4-33 MGP 462 • Software Configuration and Control Starting the contr ol pr ogram Most items in the MGP 462 configuration pr ogram can also be configured via the front panel, described in chapter 3. Refer to that chapter for details on featur es and settings. The MGP 462 software Help pr ogram provides information on settings and on how to use the[...]

  • Seite 82

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-34 MGP 462 window 5 . For information on configuring the MGP 462 using the W indows-based software, r efer to the program’s Help. T o access the Help file, select Contents from the Help pull-down menu, or press the F1 key . Using the Button Label Genera[...]

  • Seite 83

    4-35 MGP 462 • Software Configuration and Control 3. Click on the button re presentation that you want to edit. A r ed box surrounds the selected button. Button Label Generator window for the MGP 462 4 . Edit the selected button by using any of the tools provided on the Button Label Generator window . Some of the edits you can make are: • Enter[...]

  • Seite 84

    Software Configuration and Contr ol, cont’d MGP 462 • Software Configuration and Control 4-36[...]

  • Seite 85

    MGP 462 Multi-Graphic Pr ocessor 5 Chapter Five Ether net Configuration and Contr ol Accessing the Web Pages V iewing System Status Using the Configuration Pages Using the File Management Page Using the Control Pages[...]

  • Seite 86

    Ether net Configuration and Control MGP 462 • Ethernet Configuration and Control 5-2 The MGP 462 can be controlled and configur ed using HTML W eb pages accessed over a network or from a local PC connected to the MGP 462’s LAN port. The MGP 462 has factory-installed HTML W eb pages that allow you to select and configure inputs, adjust pictur e [...]

  • Seite 87

    5-3 MGP 462 • Ethernet Configuration and Control 5 . If in step 4 you entered the filename for a custom HTML page, the browser displays that page. If not, the br owser displays the System Status page, which is the MGP 462’s default start page. Y ou can select the tabs at the top of this screen to display additional screens that enable you to co[...]

  • Seite 88

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-4 Using the Configuration Pages There are five Configuration W eb pages, which only administrators can access. They are listed in the sidebar menu at the left of the Configuration scr een. The following sections describe the changes you can make from thes[...]

  • Seite 89

    5-5 MGP 462 • Ethernet Configuration and Control IP Address field The IP Address field contains the IP addr ess of the connected MGP . This value is encoded in the processor ’s flash memory . V alid IP addresses consist of four 1-, 2-, or 3-digit numeric subfields separated by dots (periods). Each field can be numbered fr om 000 through 255. Le[...]

  • Seite 90

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-6 Scaler Settings screen On the Scaler Settings screen, you can specify many configuration settings for the six inputs, the output, and windows 1 and 2. Y ou can also make changes to the screen background, select a test pattern, enable and disable Blue mo[...]

  • Seite 91

    5-7 MGP 462 • Ethernet Configuration and Control Input configuration The Input Configuration section of the Scaler Settings screen lets you name and select the video signal type for each of the six available inputs. Naming inputs Y ou can assign names to the six inputs using the input name text boxes located beneath each input number . Initially [...]

  • Seite 92

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-8 Parameters with separate menus for Window 1 and Window 2 T ext Border Color — Select a color for the border surr ounding the text label in the window . The default is Black. T ext Color — Select a color for the text displayed in the window . The def[...]

  • Seite 93

    5-9 MGP 462 • Ethernet Configuration and Control Passwords screen The Passwords scr een lets you assign an administrator and/or user password to contr ol access to the MGP 462 W eb pages. An administrator password must be in place before a user password can be assigned. Passwords must contain 4 to 12 alphanumeric characters. Symbols and spaces ar[...]

  • Seite 94

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-10 Email Alerts screen The Email Alerts screen enables you to set up the MGP 462 to automatically send e-mail alert messages when settings ar e changed on the unit. Y ou may enter up to 64 e-mail addr esses to alert recipients that an event has occurred. [...]

  • Seite 95

    5-11 MGP 462 • Ethernet Configuration and Control Setting up SMTP authorization T o set the MGP to r equire SMTP authorization before accepting any e-mail, follow these steps: 1 . T o enable the SMTP authorization fields, click the Edit button at the right of the Mail IP Address field. The Edit button changes to Save. 2 . Select the SMTP Authoriz[...]

  • Seite 96

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-12 • Select About... from the Help menu on the W indows-based contr ol software scr een. See Using the W indows-based Contr ol Softwar e in chapter 4 for more information. • Enter the appropriate SIS command. See Using Simple Instruction Set (SIS) Com[...]

  • Seite 97

    5-13 MGP 462 • Ethernet Configuration and Control Choose file window CA UTION Uploading a file with an extension other than .S19 may cause the unit to stop functioning. 3 . Open the firmware file. Its name appears in the field below the Curr ent Firmwar e V ersion on the Firmware Upgrade scr een. Firmware Upgrade screen 4 . Click the Upload butto[...]

  • Seite 98

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-14 Using the File Management Page The File Management page lets you upload files to the MGP 462 from your PC or network, and to delete files from the unit. Y ou can also upload personalized W eb pages via this screen. T o access the File Management page, [...]

  • Seite 99

    5-15 MGP 462 • Ethernet Configuration and Control Other file management activities Y ou can also perform the following tasks on the File Management screen: Opening a file — Click on the name of the file in the Files column. Deleting a file — Click the Delete button at the right end of the line that contains the file you want to remove. Deleti[...]

  • Seite 100

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-16 Window Mute Select the Enable or Disable radio button in the W indow Mute field to mute/ unmute the selected window . The corresponding Input button(s) on the fr ont panel blink continuously when the window is muted. Executive Mode Select the Enable ra[...]

  • Seite 101

    5-17 MGP 462 • Ethernet Configuration and Control Horizontal Size — Stretch or shrink the selected window horizontally . The range is determined by the output rate. V ertical Shift — Move the selected window up or down on the screen. The value in the text box is the distance in lines of the window’s top edge from the top edge of the display[...]

  • Seite 102

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-18 Contrast — Increase or decrease the range of image light and dark values in the selected window . The range is 000 to 127; the default is 064. Color — Adjust the intensity of the colors in the selected window . (At the lowest adjustment, all colors[...]

  • Seite 103

    5-19 MGP 462 • Ethernet Configuration and Control Y ou can perform the following management activities on a window preset after you select the preset name from this scr een. Naming a window preset T o change the name of a preset, follow these steps: 1 . Select a preset by clicking its button. The name of your selected pr eset is displayed in the [...]

  • Seite 104

    Ether net Configuration and Control, cont’d MGP 462 • Ethernet Configuration and Control 5-20 Input Presets scr een Y ou can perform the following management activities on an input preset after you select its number from this screen. Saving (creating) an input pr eset T o save all the settings for the currently selected input as a preset: 1 . C[...]

  • Seite 105

    MGP 462 Multi-Graphic Pr ocessor 6 Chapter Six Special Application Connecting the MGP 462 to a Matrix Switcher[...]

  • Seite 106

    Special Application MGP 462 • Special Application 6-2 This chapter describes a special type of application that repr esents unique conditions. For the MGP 462 to operate pr operly in this situation, it is important to configure it correctly . The following pages describe an example of an application involving connection to a matrix switcher , alo[...]

  • Seite 107

    6-3 MGP 462 • Special Application • Input presets are r ecalled on the MGP to corr ectly set up the input coming from the switcher . This setup can include the video signal type; pictur e controls; advanced input configuration functions such as setting the active lines/pixels, total lines/pixels, and pixel phase; and the input name. Y ou can pe[...]

  • Seite 108

    Special Application, cont’d MGP 462 • Special Application 6-4 Synchronizing the MGP 462 to the matrix switcher The W indows-based control softwar e contains a tool that synchronizes the MGP to a connected matrix switcher . The synchronization tool does the following: • Provides the ability to automatically r ecall input presets when a switch [...]

  • Seite 109

    6-5 MGP 462 • Special Application 4 . Click the Connect T o Matrix button located to the right of the IP Address field. When the connection is made, the size of the matrix switcher is displayed to the right of the Connect T o Matrix button. Sync MGP to Matrix Switcher window showing matrix size 5 . Important: On your MGP , make sure that input 1 [...]

  • Seite 110

    Special Application, cont’d MGP 462 • Special Application 6-6 Additional setup procedur es if using a third party control system without the MGP Sync tool When operating the system using a third-party control system, you can prevent the image from blanking or scrambling on the display during input switches by performing the following additional[...]

  • Seite 111

    MGP 462 Multi-Graphic Pr ocessor A Appendix A Specifications, Part Numbers, and Accessories Specifications Included Parts Accessories[...]

  • Seite 112

    Specifications, Part Numbers, and Accessories MGP 462 • Specifications, Part Numbers, and Accessories A-2 Specifications Video input Number/signal type ................... 4 RGBHV, RGBS, RGsB, RGBcvS, component video, S-video, composite video 1 component video (interlaced), S-video, composite video 1 optional digital component video (SDI, 270 Mbp[...]

  • Seite 113

    A-3 MGP 462 • Specifications, Part Numbers, and Accessories Max input voltage ....................... 5.0 Vp-p Polarity .......................................... Positive or negative (selectable) Control/remote — processor/decoder/scaler Serial control port ........................ RS-232 or RS-422, 9-pin female D connector Baud rate and proto[...]

  • Seite 114

    Specifications, Part Numbers, and Accessories, cont’d MGP 462 • Specifications, Part Numbers, and Accessories A-4 Included Parts These items are included in each or der for an MGP 462: Replacement Included parts part number MGP 462 60-623-01 MGP 462D 60-623-02 MBD 149 rack mounting kit 70-077-03 IEC power cord 27-044-01 Rubber feet (self-adhesi[...]

  • Seite 115

    MGP 462 Multi-Graphic Pr ocessor B Appendix B Installing the SDI Car d Installing a Serial Digital Interface (SDI) Card[...]

  • Seite 116

    Installing the SDI Card MGP 462 • Installing the SDI card B-2 Installing a Serial Digital Interface (SDI) Card The optional SDI input card may be installed in the MGP 462 if the unit does not already have an input for a serial digital interface signal. The following pictur e shows the MGP 462 with the SDI card installed. MGP main board with SDI i[...]

  • Seite 117

    B-3 MGP 462 • Installing the SDI Card CA UTION Do not touch any switches or other electronic components inside the MGP 462. Doing so could damage the unit. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. Y ou must be electrically grounded befor e proceeding with any electronic component replacement. A grounding w[...]

  • Seite 118

    Installing the SDI Card, cont’d MGP 462 • Installing the SDI card B-4 7 . The SDI input car d has a 20-pin socket on the underside which must align with the 20 pins on the main cir cuit boar d. Be sur e to align the pins pr operly to prevent bending them, before pr essing the SDI card down firmly in place onto the standoff. The mounting hole on[...]

  • Seite 119

    B-5 MGP 462 • Installing the SDI Card 9 . Install the metal hex nut around the SDI connector on the back panel of the unit. Keep the SDI card from twisting as the nut is tightened. Hex nut installed around SDI connector 10 . Replace the top cover on the unit, and fasten it with the screws that were removed in step 3 . 11 . Rack mount the MGP 462,[...]

  • Seite 120

    Installing the SDI Card, cont’d MGP 462 • Installing the SDI card B-6[...]

  • Seite 121

    MGP 462 Multi-Graphic Pr ocessor C Appendix C Firmwar e Update Guide Determining the Firmware V ersion Downloading the Firmware Updating the Firmware[...]

  • Seite 122

    Firmware Update Guide MGP 462 • Firmware Update Guide C-2 Updates to the Extron MGP 462 Multi-Graphic Pr ocessor firmware ar e made available periodically via the Extron W eb site. If the need arises, you can r eplace the MGP 462’s main firmwar e via an IP connection without opening the unit or changing firmware chips. Determining the Firmware [...]

  • Seite 123

    C-3 MGP 462 • Firmware Update Guide Example of a password prompt window a . Enter the appropriate administrator passwor d in the Password field. A User name entry is not required. b . If desired, select the check box to have the system input your password the next time you enter your MGP 462’s IP addr ess. c . Click OK. The System Status page o[...]

  • Seite 124

    Firmware Update Guide, cont’d MGP 462 • Firmware Update Guide C-4 About MGP screen 3 . When finished viewing the information, click OK to close the window . Downloading the Firmware T o obtain the latest version of MGP 462 firmwar e, follow these steps: 1 . V isit the Extron W eb site (www .extron.com) and go to the MGP 462 page. 2 . Click Down[...]

  • Seite 125

    C-5 MGP 462 • Firmware Update Guide Updating using the Web pages Follow these steps to update the firmware using the W eb pages: 1. Launch a W eb browser (for example, Internet Explor er) on the connected computer , and enter your MGP’s IP address in the addr ess field. 2 . If no password has been assigned, the MGP 462 W eb page opens, displayi[...]

  • Seite 126

    Firmware Update Guide, cont’d MGP 462 • Firmware Update Guide C-6 Choose File screen with firmware file selected 5 . On the Choose file window , open the firmware file. Its name appears in the field below the Current Firmware V ersion on the Firmwar e Upgrade scr een. 6 . Click the Upload button on the Firmware Update screen to start the firmwa[...]

  • Seite 127

    C-7 MGP 462 • Firmware Update Guide Open window with firmwar e file selected 3 . Browse to locate the firmware file that you saved to your computer . The file extension must be .S19. CA UTION Uploading a file with an incorrect extension may cause the unit to stop working. 4 . Double-click on the firmware file icon. The firmware uploading pr ocess[...]

  • Seite 128

    Firmware Update Guide, cont’d MGP 462 • Firmware Update Guide C-8[...]

  • Seite 129

    FCC Class A Notice Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can rad[...]

  • Seite 130

    © 2006 Extron Electronics. All rights reserved. Extron Electr onics, USA 1230 South Lewis Str eet Anaheim, CA 92805 USA 714.491.1500 F ax 714.491.1517 Extron Electr onics, Europe Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 F ax +31.33.453.4050 Extron Electr onics, Asia 135 Joo S eng Road, #04-01 PM Industrial Building Sing[...]