Epson XK3190-A1+P Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Epson XK3190-A1+P an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Epson XK3190-A1+P, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Epson XK3190-A1+P die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Epson XK3190-A1+P. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Epson XK3190-A1+P sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Epson XK3190-A1+P
- Den Namen des Produzenten und das Produktionsjahr des Geräts Epson XK3190-A1+P
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Epson XK3190-A1+P
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Epson XK3190-A1+P zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Epson XK3190-A1+P und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Epson finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Epson XK3190-A1+P zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Epson XK3190-A1+P, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Epson XK3190-A1+P widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    XK3190-A1 +P Weighing Indicator USER ’ S GUIDE Attention: Please read this User’s Guide carefully when you use the indicator![...]

  • Seite 2

    X K 3 1 9 0 - A 1 +P 1 . Specifications 2 . Installation 2.1 Front & Back View of Indicator 2.2 Keyboard Function 2.3 Connecting Loadcell to Indicator 3. Calibration 4. Operating Instructions 4.1 Starting and Starting auto zero setting at turning on 4.2 Manual Zero Setting (Semi-automatically setting zero ) 4.3 Tare Function 4.4 Connecting Scor[...]

  • Seite 3

    X K 3 1 9 0 - A 1 +P 1 Specification 1 Model XK3190-A1 + 2 Sample rated 5~25 times / sec 3 Load cell sensitivity 1~ 2mv/v 4 Division 1/2/5/10/20/50/100 optional 5 Display 7-bits LED digital display 0.56” in character height and 7 status indicating. 6 Clock can display day/month/year and second/minute/hour 7 Scoreboard display interface Using seri[...]

  • Seite 4

    X K 3 1 9 0 - A 1 +P 2. Installation 2.1 Front & Back View of the Indicator 1 ACCU 2 PRE-T 3 FUN TARE ENTER 4 CLEAR 5 CHECK 6 DATE 0 STORE WEIGH 7 SET PRINT 8 CALB 9 TIME PRINT ZERO UNIT:KG MONEY PRICE AUTO DATE TIME TARE STABLE (Graph 2-1) Front View of Indicator * ACCU - accumulating FUN- function CALB – Calibrating ( 2 5 ) p i n s ( 1 5 ) [...]

  • Seite 5

    X K 3 1 9 0 - A 1 +P 2.2 Keyboard Function Key Function 1 [ACCU],[ UNIT PRICE] No meaning 2 In calibration mode, pressing [PRE-TARE/2] , can input digital key “2”; In weighing mode, the key is used for presetting tare. 3 [DELETE/4] In calibration mode, pressing [DELETE/4], can input digital key “4”; In weighing mode, it is deleting function[...]

  • Seite 6

    X K 3 1 9 0 - A 1 +P 15 In calibration or parameters setting mode, pressing [ weigh], it will exit from original calibration or setting mode and return to weighing mode. 2.3 Connecting Loadcell to Indicator 1. The 9-pin socket is used for the link-up of loadcell, which has been clearly shown in the graph 2-3. 2. The 4-pin shielded cable is used, +S[...]

  • Seite 7

    X K 3 1 9 0 - A 1 +P 3. Calibration According to the Graph 2-3, connecting Indicator and loadcell, and the indicator enters weighing mode. 1. Connecting calibration jumper to the 15- pin socket on the indicator back panel. (There is a 15-pin plug in the packing carton with its 14-pin short connected with 15-pin. ) 2. According to table 4-3, carry o[...]

  • Seite 8

    X K 3 1 9 0 - A 1 +P step Operation Display Explanation 8 press [ 1 ] [ 5 ] [ 0 ] [0 ] press [ Enter ] [ A LoAd1] [ d 1500 ] Loading weight ≥ 5% Max. 。 Example: 1500 After stable light is on, press [ Enter ] key. 9 press [ Enter ] [ noLoAd ] Confirming zero position again. 10 press [2] [0] [0][0] [0] press [ Enter ] [ ALoAd2 ] [ 20000 ] Reloadi[...]

  • Seite 9

    X K 3 1 9 0 - A 1 +P out. 4. . Operating Instructions 4.1 Power on 1 When using AC power , power on , setting the ship- form switch at the back cover of the indicator on “1” ; If using DC power , setting the ship- form switch at the back cover of indicator on “1”, then pressing the recover switch, the indicator will perform “999999 - 0000[...]

  • Seite 10

    X K 3 1 9 0 - A 1 +P (Graph 4-1) Serial Communication port and score display port 4.4 Connecting Scoreboard to Indicator 1. The display interface of scoreboard is 15-pin socket, which has been clearly shown in the Graph 4-1. 2. The scoreboard signal is 20mA continuous current loop, outputting in binary code, the baud rate is 600. 4.5 Connecting Pri[...]

  • Seite 11

    X K 3 1 9 0 - A 1 +P ▲ The printer must be compatible to the indicator, please choose the recom mended printer. ▲ The printer GND can not be connected to the power GND, otherwise the indicator or printer will be destroyed. 3. Set print parameters step operating display Explanation 1 press [PRN Set ] press [ 9 ] [ 7 ] press [ Enter ] [ P 00 ] [ [...]

  • Seite 12

    X K 3 1 9 0 - A 1 +P Press[Enter] [ dct ] 1: use discount End Note: You can use discount only when the blank filling mode is selected. 4. print and print format Press [PRINT] key, you can print required weighing data according to print setting. Record Format: Weight Bill D a t e 9 7 - 0 1 - 3 1 NO. Time Gross ( kg ) Tare ( kg ) Net ( kg ) Accumulat[...]

  • Seite 13

    X K 3 1 9 0 - A 1 +P REMARK ★ If setting the odE parameter to 1, you can perform the blank filling priting, at this time the other priting formats a re invalid (Records format and document format are invalid). Method: pushing [print] key, if dct parameter is set to 1, it will display [BFL **], inputting the discount rate and pushing [Input], it w[...]

  • Seite 14

    X K 3 1 9 0 - A 1 +P communication m ode parameters. (2) The sequence of parameters setting as following: Connecting the loadcell , the indicator enters into working mode which is shown in the Graph 2-3. Insert the setting jumper into 15-pin socket at the back of indicator. (There is a 15-pin plug in the packing carton with its 14-pin shorte connec[...]

  • Seite 15

    X K 3 1 9 0 - A 1 +P [ Enter] key or [weighing] key to exit. If it is incorrect, using digital keys enters new date , then press [ Enter ] key. ( 2 ) Under weighing status of the indicator, pr ess [ Time ] key, and Time sign lamp is lighted. Indicator display original Time data at this time. If it is correct, then press [ Enter ] key or the [ w[...]

  • Seite 16

    X K 3 1 9 0 - A 1 +P 3 Clear Press [ clear ] key, can clean accumulating weight value or stored data. Step Operating Display Explanation 1 press [ Clear ] 2 press [ 1 ] [ sure 1 ] [ sure 0 ] [ sure 1 ] Selecting clear/not clear 0: no 1: yes Example: 1 End 4.9 Insufficient voltage indicating When the storage cell voltage is insufficient, the insuffi[...]

  • Seite 17

    X K 3 1 9 0 - A 1 +P electronic components will be damaged and electric shock is likely to happen. 5.6 You should cut off power supply of indicator a nd relevant device before you pull-in and out the connecting line of indicator and external device. ▲ ! You must cut off power supply of the indicator , before you plug the connecting line of the [...]

  • Seite 18

    X K 3 1 9 0 - A 1 +P 6.3 Wrong setting information indicating 1 Err 13 Wrong setting of the division value . 2 Err 14 Decimal point must be less than 5, please reset the decim al bit. 3 Err 15 Overload warning must be > 100, please reset it. Err 17 Enter new data which should be less than 65000. 6.4 Wrong connection information indicating 1 Err [...]

  • Seite 19

    X K 3 1 9 0 - A 1 +P 3 Err 21 Calibrating data have been lost in RAM and EPROM, Operator must p u t in the calibration plug, then reenter the original calibration data, turn o n t h e i n d i c a t o r a g a i n o r r e - c a l i b r a t e i t . 4 Err 22 EPROM has been damaged. 5 Err 23 RAM has been damaged. 6.6 Other information indicating 1. Err [...]

  • Seite 20

    X K 3 1 9 0 - A 1 +P The frame from the com puter consists of 6 data explanation 1 0 2 ( X O N ) s t a r t 2 A ~ Z a d d r e s s 3 A: Shaking hands B: asking GW C: asking tare D: asking NW E: asking accumulated times and accum ulated weight 4 X R L c h e c k i n g 5 X R L c h e c k i n g 6 0 3 ( X O F F ) e n d X R L = 2 ⊕ 3[...]

  • Seite 21

    X K 3 1 9 0 - A 1 +P The explanation of data No : 4 - n Comma nd A No data Each frame consists of 6 groups of data Comma nd B G W : + / - G W d a t a ( 6 b i t s ) . . . G W d a t a D e c i m a l p o s i t i o n Each frame consists of 14 groups of data Comma nd C Tare: + / - T a r e d a t a . . . T a r e d a t a D e c i m a l p o s i t i o n Each f[...]

  • Seite 22

    X K 3 1 9 0 - A 1 +P Comma nd E Accumulated times and weigh Accumulated times (4 bits ) . . . , (comma) separation m ark Accumulated weight (10 bits ) . . Decimal position Each frame consists of 22 groups of data[...]