DMP Electronics XR500 Bedienungsanleitung

Pr ogramming guide Xr500 SerieS Canadian Command ProCeSSor™ P anel[...]

MODEL XR500 SERIES CANADIAN ACCESS CONTROL COMMAND PROCESSOR™ PANEL PROGRAMMING GUIDE Contains progr amming Instructions for use with the Model XR500, XR500N, XR500E Canadian Access Control Command Pr ocessor™ Panels. When using the XR500 Series Canadian panel for any UL C other listing organization’ s approved methods, refer to this manual a[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products i T able of ConTenTS 1.1 Before you Begin ................................................................. 1 Programming I nformation Sheet ........................................... 1 1.2 Getting Started .................................................................... 1 1.3 [...]

Digital Monitoring Products XR500 Series Canadian Programming Guide ii T able of ConTenTS 4.3 Gateway Address ................................................................13 4.4 Subnet Mask ......................................................................13 4.5 DNS Server .....................................................................[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products iii T able of ConTenTS 7 .5.2 Encrypt Network Remote .....................................................23 7 .6 Allow Cellular Remote ......................................................... 23 7 .6.1 First GPRS APN / Second GPRS APN ..................................... 23 7 .6[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide iv T able of ConTenTS Output Options................................................................33 11.1 Output Options ................................................................... 33 11.2.1 Cutoff Output ...................................................................[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products v T able of ConTenTS 17 .9 User Command Reports ....................................................... 42 17 .10 Door Access Reports ........................................................... 43 17 .11 Supervisory Reports ..........................................................[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide vi T able of ConTenTS 19.13 Alarm Action.......................................................................56 19.14 Disarmed Open .................................................................56 19.15 Report to T ransmit ......................................................[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products vii This page intentionally left blank.[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 1 inTroduCTion Introduction 1.1 Before you Begin This guide provides programming information for the DMP XR500, XR500N, and XR500E Command P rocessor™ Panel. After this Introduction, the remaining sections describe the functions of each programming menu item along with the availa[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 2 inTroduCTion 1.3 Encrypted Communications (XR500N/XR500E only) Some installations require secure data communications. DMP offers NIST approved AES encrypted communication. Use a unique passphrase to enable encrypted communications and provide a secure meansfordatacommuni[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 3 inTroduCTion 1.7 Power Up WhentheXR500SeriesCanadianpanelispoweredupafteran ACpowerfailure,anyzonetransitionsare notrecognizedfor60seconds.Normalzoneprocessingresumesattheendofthe60[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 4 inTroduCTion 1.10 Entering Alpha Characters Some options during programming require you to enter alpha characters. T o enter an alpha character , press or touch the key that has that letter written below it. The keypad displays the number digit of the key .Next,presst[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 5 inTroduCTion 1.13 Multiple Displays For many programming and user options, such as Area selections, Menu Displays, and Status Lists , there are several displays containing programming. For example, when programming Menu Displays, keypads 1 through16displayontwosepa[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 6 iniTializa Tion Initialization NOTE: WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN AND ‘SAVING PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE PROGRAMMING CHANGES. SEE SECTION 17.1. 2.1 INITIALIZA TION Initialization This function allows you to [...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 7 iniTializa Tion 2.9 COM/RMT? NO YES SURE? YES NO Clear Communication and Remote Options NO - Leavesexistingcommunicationandremoteoptionsintact. YES - Clears communication and remote options programming to factory defaults. 2.10 DEF AUL TS NO YES SURE? YES NO Set[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 8 CommuniCa Tion Communication 3.1 COMMUNICA TION Communication Congurethecommunicationoptionsforthepanel.Theinformationyouprogram varies with the Communication T ype you select. 3.2 ACCOUNT NO: 12345 Account Number The Account Number is a 1 t[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 9 CommuniCa Tion 3.6 PA TH TYPE: BACKUP Path Type TheP athT ypedenesifthepathisPrimaryorBackup.BecauseP ath1isP rimary , thispromptonlydisplaysforpaths2-8.DefaultisBackup. Note: IftheP rima[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 10 CommuniCa Tion 3.15 RECEIVER POR T - Receiver Port 2001 Enterthereceiverportnumber .V alidrangeis1to65,535.Defaultis2001. 3.16 FIRST PHONE NO. First Telephone Number This option displays only if the Communication T ype is DD or [...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 11 CommuniCa Tion 3.22 RETRY SECONDS: 6 Retry Seconds This option displays for NET or 232 Communication T ypes. Enterthenumberofseconds(between6and15)thepanelshouldwaitbefore retrying to send a message to the receiver if an acknowledgment w[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 12 CommuniCa Tion 3.29 ALARM YES Alarm Reports This prompt displays when the P ath T ype is P rimary . All backup paths within the group follow the same programming for Alarm Reports. Default is Y es. NO YES FIRE WhenYESisselected,thefollowingreportsarese[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 13 neTw ork oPTionS Network Options (XR500N/XR500E only) NetworkOptionsareprovidedtodenethenetworkcongurationforthepanel.Thisinformationwillbe used during communication of messages via network or email. Note: IPaddressesan[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 14 meSSa ging SeTuP Messaging Setup 5.1 MESSAGING SETUP Messaging Setup This section allows you to enter the information needed to receive messages directly from the panel via email and In T ouch™ SMS T ext using Network or Cellular communication. All of the name and password opt[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 15 meSSa ging SeTuP 5.9 Destination 3 User Number If Destination 3 is a cellular number , enter the user’ s User Number for arming/disarmingauthorization. 5.10 EMAIL COMM T YPE Email Communication Type NET CELL ChoosingNETsendsemailmessagesoverthenetwork.?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 16 deviCe SeTuP Device Setup 6.1 DEVICE SETUP Device Setup ThissectionallowsyoutodenetheXR500SeriesCanadianpanelphysical conguration.Y oucaninstallandaddressuptosixteen superv ised devices on the keypad data bu[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 17 deviCe SeTuP 6.6 DISPLA Y AREAS: Display Areas *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 *13 *14 *15 *16 *17 *18 *19 *20 *21 *22 *23 *24 *25 *26 *27 *28 *29 *30 *31 *32 P resstheCOMMANDkeytoprogramDisplay Areas.T oselectanareabetween1[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 18 deviCe SeTuP 6.7 STRIKE TIME: 5 Strike Time ThisoptiondisplaysifDOORisselectedasDeviceT ype. Enter a door access time, between 1 and 250 seconds, during which a keypad or access control device relay is activated. Magnetic locks or electric door stri[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 19 deviCe SeTuP 6.15 PROGRAM 734 Program 734 Options OPTIONS? NO YES Select YES toprogramthe734WiegandInterfaceModule.Devicetypemustbesetto DOOR. 6.15.1 Activate Zone 2 Shunt SelectYEStoactivatetheSoft-Shunt™option.?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 20 deviCe SeTuP 6.15.6 ACTIV A TE ONBOARD SPEAKER? NO YES Activate Onboard Speaker SelectYEStoenabletheonboardpiezospeakerforlocalannunciation.SelectNOto turn the piezo off for all operations. This does not affect remote annunciator open[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 21 deviCe SeTuP 6.15.9 REQUIRE SITE CODE? NO YES Require Site Code P ress the top row Select key under YES to use a site code. InadditiontoUserCodeverication,dooraccessisonlygrantedwhenanyonesite codeprogrammedattheSITE[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 22 remo Te oPTionS Remote Options 7.1 REMOTE OPTIONS Remote Options ThissectionallowsyoutoentertheinformationneededforR emoteCommand/ R emote P rogramming operation. 7.2 REMOTE KEY : Remote Key Thisoptionallowsyoutoenteracode[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 23 remo Te oPTionS 7.4.3 PC Modem YESallowsthepaneltoanswerthetelcolinkandconnectwithR emoteLinkthrough thePCModemat2400baud.NOdisablesPCModemcommunication. 7.4.4 Manufacturer Authorization Select YES to [...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 24 remo Te oPTionS 7.8.4 Entré Backup IP Address ThisoptiondisplaysonlyifNET ischosenfortheEntréconnection.EntertheIP   backupaddresswherethepanelsendsnetworkmessagesiftherstEntréIP?[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 25 Sy STem rePor TS System Reports 8.1 SYSTEM REPOR TS System Reports Selectspecicsystemreportsthepanelsendstothereceiver . 8.2 ABORT NO YES Abort Report YES allows the panel to send an alarm abort report to the receiver any time an area is disarmed du[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 26 Sy STem rePor TS 8.8 AMBUSH NO YES Ambush YES allows an ambush report to be sent anytime user code number 1 is entered at akeypad.NOdisablestheambushreportandallowsusernumber1tooperatethe same as all other codes. 8.9 PANIC T ST NO [...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 27 Sy STem oPTionS System Options 9.1 SYSTEM OPTIONS System Options Thissectionallowsyoutoselectsystem-wideparameters. 9.2 SYSTEM: AREA System This option allows you to program how the areas operate for arming and disarming. The options you can choose are liste[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 28 Sy STem oPTionS 9.6 CRS ZONE TM: 4 Cross Zone Time Enterthetimeallowedbetweenzonefaults.Whenzonesarecrosszoned,thesame zone or a second cross zoned zone must fault within this time in order for an alarm report for both zones to be sen[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 29 Sy STem oPTionS GMT City/Time Zone GMT City/Time Zone 0 London, Monrovia, Lisbon, Dublin, Casablanca, Edinbur gh 13 New Cadelonia 1 Cape V erde Island, Azores 14 Guam, Sydney 2 Mid-A tlantic, Fernando de Noronha 15 T okyo, Seoul 3 Buenos Aires, Georgetown, Brasilia, Rio de Janei[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 30 Sy STem oPTionS Forexample,whenSpanishisselectedatakeypad,theUserMenuandStatusList text display in Spanish at that keypad.Whentheuserlateraccessesthekeypad, pressingtheCOMMANDkeyoncedisplays?[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 31 Sy STem oPTionS 9.19 WLS AUDIBLE: DAY WIRELESS AUDIBLE ANY DAY MIN Wireless Audible Annunciation ThisoptiondisplayswhentheHouseCodeenteredisforaDMP1100SeriesWireless system(1-50).P ressanytoprowkeytoselect?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 32 bell oPTionS Bell Options 10.1 BELL OPTIONS Bell Options This section allows you to program the panel bell output functions. 10.2 BELL CUT OFF: 15 Bell Cutoff Time Enterthemaximumtimefrom1to99minutestheBellOutputremainson.Ifthe?[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 33 ouTPuT oPTionS Output Options 11.1 OUTPUT OPTIONS Output Options This section allows you to program panel output options. The panel provides two FormCrelays(1and2)andfourswitchedground(opencollector)outputsnumbered 3to6.Expan[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 34 ouTPuT oPTionS 11.6 PANIC ALM OUT : 0 Panic Alarm Output Enter the output number to turn on when any P anic type zone is placed in an alarm condition. The output is turned off after all P anic zones are restored from an alarm conditionandaSensorR esetisperforme[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 35 ouTPuT oPTionS 11.15 CLS WAIT OUT : 0 Closing Wait Output Entertheoutputnumbertoturnonforapproximatelyfour(4)secondswhenClosing W aitisprogrammedasYESandthepanelsuccessfullycommunicatestheclosing messa[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 36 ouTPuT informa Tion Output Information 12.1 OUTPUT INFO Output Information This section allows you to program wireless outputs and name wired outputs. 12.2 OUTPUT NO. X X X Output Number Enteranoutputnumber .Entryrangeis1to6,450to474,480[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 37 ouTPuT grouPS Output Groups 13.1 OUTPUT GROUPS Output Groups Thisfunctionallowsyoutoassignoutputstogroups.Outputgroupscanbeassigned tootherareasofprogrammingsuchasOutputOptionsor Alarm ActionofZo[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 38 menu diSPla y Menu Display 14.1 MENU DISPLA Y Menu Display Menu Display allows you to select at which keypad addresses the user can access the following functions. T oselectakeypad,enterthedevicenumber(keypadaddress)usingthedigitkeys on?[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 39 ST a TuS liST Status List 15.1 ST A TUS LIST Status List This function allows you to select the zone alarms and troubles, and system monitor troublesdisplayedatthekeypads.TheStatusListfunctionoperatesautomatically when the keypad is not perfor[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 40 ST a TuS liST 15.5 BURGLAR Y ZONES: Burglary Zones Speciesthekeypadaddresses(1through16)whereallburglaryzonealarmsand troubles display . Bur glary zones in clude Night, Day , and Exit type zones. Burglary zone troubles remain in the list[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 41 PrinTer rePor TS Printer Reports 16.1 PRINTER REPOR TS Printer Reports Thissectionallowsyoutodenetheoperationofalocalprinterconnectedtothe panelthroughtheuseofaDMP462P P rinterInterfaceCard.The?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 42 PC log rePor TS PC Log Reports 17.1 PC LOG REPOR TS PC Log Reports ThissectionallowsyoutoprogramthetypesofPCLogR eportsthepanelsends throughthe462NNetworkInterfaceCardorthroughtheJ21SerialConnector [...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 43 PC log rePor TS 17.10 DOOR ACS NO YES Door Access Reports Sends door access activity: door number , user number and name, and time and date. 17.11 SUPV MSG NO YES Supervisory Reports Sends system monitor reports, such as AC and battery , and system event reports. Supervisory R e[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 44 area informa Tion Area Information 18.1 AREA INFORMA TION Area Information Allowsyoutoassignfunctionstothedifferentareasinthesystem. Allnon-24-hour zonesmustbeassignedtoanactivearea.SeeZoneInformation.[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 45 area informa Tion 18.5 CLS CHK NO YES Closing Check Select YES to enable the panel to verify that all areas in the system are armed afterpermanentorextendedsched ulesex pire.IftheClos ingCheckndsanyareas disarmed past the sch[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 46 area informa Tion 18.10.2 INT BDRM PERIM Home/Sleep/Away Programming WhenHome/Sleep/A wayisselectedasthesystemtype,programtheInterior , Bedroom, and P erimeter areas as needed. 18.11 * UNUSED * Area Name The area name can be up to 32 alphanumeric[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 47 area informa Tion 18.16 ARMED OUTPUT : 0 Armed Output Number Enter the output to turn on when this area is armed. If an exit delay is used for this area,the ArmedOutputturnsonatthestartoftheexitdelay .Theoutputisturned off wh[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 48 zone informa Tion Zone Information 19.1 ZONE INFORMA TION Zone Information ZoneInformationallowsyoutodenetheoperationofeachprotectionzoneusedin the system. All protection zones, whether located on a command processor panel, Security C[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 49 zone informa Tion 19.4 ZONE T YPE: BL ANK Zone Type TheZoneT ypedenesthepanelresponsetothezonebeingopenedorshorted. This is called the Alarm Action. There are up to 13 possible alarm action responses dependingonthezonet[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 50 zone informa Tion 19.7 ARM/DIS AREAS Arming Zone Area Assignment Inan AreaorHome/Sleep/A waywithGuestsystem,ifthezonehasbeen programmedasan ArmingT ype(AR),entertheareasthatthezonecontrols. Whenthez[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 51 zone informa Tion 19.9 NEXT ZN? NO YES Next Zone SelectYEStoterminatezoneprogramming. ThedisplayreturnstoZoneNumber , allowingyoutoenteranewzonenumber .SelectNOtomakealter ationstothe Alarm[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 52 zone informa Tion TRANSMTR CONT ACT 1 2 3 4 Thisoptiondisplayswhenprogrammingthe1114WirelessFour-ZoneExpander with four input contacts. The same serial number is used for all four contacts. Selectthecontactnumbertoprogram.When?[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 53 zone informa Tion 1100 Series Key Fobs F or an 1100 Series Key F ob set the House Code from 1 to 50. See House Code programming in System Options.Onlyzones400to449canbeprogrammedas1100SeriesKeyFobzones.R efertothe1100?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 54 zone informa Tion 19.11.7 BUT TON ACTION yyy: XXX XXX XX Button Action ThisoptionspeciestheButton Actionforanindividualkeyfobbutton.The default action for the button selected is displayed. P ress any Select key to displaytheButt[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 55 zone informa Tion ARM AREAS: PERIM  Inan All/P erimeterorHome/Sleep/A waysystem,thisspeciestheareatobe armedbytheK eyFobbuttonbeingprogrammed.For All/P erimetersystems, choosePERIMor ALL,fo[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 56 zone informa Tion FA Series Wireless F or an F A Series Remote Wireless Receiver settheHouseCodeto99.SeeHouseCodeprogrammingin SystemOptions.Onlyzones500to699canbeprogrammedasF A SeriesWirelesszo[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 57 zone informa Tion 19.15 MSG: TROUBLE Report to Transmit P ressanySelectkeytodisplaythefollowingreportoptions: A,T ,L,S,C,and-(dash). A T L - ALARM - Select A to send an alarm report to the receiver and activate the bell output a[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 58 zone informa Tion 19.18 SWGR BYP NO YES Swinger Bypass Selecting YES allows the zone to be swinger bypassed by the panel according to the specications pro grammed in Swinger Bypass T rips and R eset Swinger Bypass.  The Bypass conditi[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 59 zone informa Tion 19.25 PRIORIT Y NO YES Priority Select YES to provide additional protection for the premises by requiring this zone to be in a normal condition before its assigned area can be armed. 19.26 Fire Panel Slave Input ThisoptionisavailableonFireZone[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 60 ST oP Stop 20.1 STOP Stop Save Progr amming WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN AND ‘SAVING PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE PROGRAMMING CHANGES. AttheST OPprompt,pressinganySelectkeyallowsyou[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 61 fea Ture uPgrade Feature Upgrade 22.1 FEA TURE UPGRADE Feature Upgrade IntheP rogrammingMenu,pressingCOMMANDattheSETLOCKOUT CODEprompt displaysFEA TUREUPGRADE.Thisallowsyoutoenableadditionalfeaturesinthe [...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 62 aPPendiX Appendix 23.1 False Alarm Reduction System Recently Armed report TheSystemR ecently Armedreport(S78)issenttothereceiverwhenaburglaryzonegoesintoalarm within two minutes of the system being armed. 23.2 Diagnostics fun[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 63 aPPendiX MAC Address ShortforMedia AccessControladdress.Thishardwareaddressuniquelyidentieseachnetworknode.Not to be confused with an IP address, which is assignable. In the Diagnostics function, the MAC address is the panel?[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 64 aPPendiX 23.3 Using the 984 Command Function Thisfeatureallowsyoutoconnecttoaservicereceiver ,isusedprimarilytobringanewaccounton-line anduploadpanelprogrammingcompletedinR emoteLink™. Note:[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 65 aPPendiX 23.4 Using the Walk Test The XR500 Series Canadian panel provides a walk test feature that allows a single technician to test the protectiondevicesconnectedtozonesonthesystem.ConducttheW alkT estwithin30minutesofresetti[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 66 aPPendiX If ENHANCED ZONE TEST is selected as YES: A V erify message is sent at the time the zone trip occurs instead of at the end of the W alkT est.ForFI,FVorSVzonetypes,theV erifymessageissentattheinitialtrip. For al[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 67 aPPendiX 23.6 Cross Zoning CautionmustbetakenwhencrosszoningdevicestoensurethattheCrossZoneT imeislongenoughto allowanintrudertotripbothdevicesbeforeitexpires. A CrossZoneT imet[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 68 aPPendiX Prole # ProleName Arm/Disarm Areas Access Areas Output Group Arm Disarm Alarm Silence Sensor Reset Door Access Armed Area Outputs On/Off Zone Status Bypass Zones Zone Monitor System Status System Test UserProles User Codes Schedules Time Display Events[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 69 aPPendiX 23.10.1  WirelessCheck-inandSupervisionDenitions FA Series Check-in Time Explained Thecheck-intimeprogrammedforF A Serieswirelesstransmittersisthenumberofsecondsbetween each message sent from the transmitter[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 70 aPPendiX Keypad Bus Zone Information T ype Area Fire Bell Disarmed Open Disarmed Short Armed Open Armed Short Swinger Prewarn Entry Delay Retard Delay Presignal F ast Response Cross Z one Priority Follow Area Real- Time Rprts Door Number Style Assign Disarm condition of NT , DY [...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 71 aPPendiX 23.12.2 LX-Bus Zone Type Defaults These are complete spellings of the abbreviations used for the zone types, such as Night and Exit. T ype -Thesearetheabbreviationsusedforthezonetypes, such as NT and EX. Area -Foran Areaor[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 72 aPPendiX 23.13 Common Keypad Messages There are several common keypad messages that the keypad displays to inform the technician and end-user .Thecommonmessagesaredescribedbelow .P ossiblesolutionsarealsoprovided. Message Meaning Poss[...]

XR500 Series Canadian Programming Guide Digital Monitoring Products 73 aPPendiX 23.14 Area Account Number Messages XR500 systems send an area account number instead of the system account number with the following panelmessages/eventsbasedontheareaassignedtothezonethatinitiatedthealarm: W ARNING: AlarmBel[...]

Digital Monitoring Products XR500 Series Canadian Programming Guide 74 reviSionS Revisions to This Document Thissectionexplainsthechangesmadetothisdocumentduringthisrevision.Itliststheversion,identies thechange(s)made,therelatedsectionnumberandheading,andasumm[...]

L T -0679CAN1.08©2010DigitalMonitoringProducts,Inc. 800-641-4282 www .dmp.com Made in the USA INTRUSION•FIRE• ACCESS•NETWORKS 2500 North P artnership Boulevard Springfield,Missouri65803-8877 10392 Listings and Approvals This Class A digital apparatus complies with Canadian ICES-003 NIST V alidated[...]