Crimestopper Security Products CS-2004DC Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Crimestopper Security Products CS-2004DC an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Crimestopper Security Products CS-2004DC, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Crimestopper Security Products CS-2004DC die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Crimestopper Security Products CS-2004DC. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Crimestopper Security Products CS-2004DC sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Crimestopper Security Products CS-2004DC
- Den Namen des Produzenten und das Produktionsjahr des Geräts Crimestopper Security Products CS-2004DC
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Crimestopper Security Products CS-2004DC
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Crimestopper Security Products CS-2004DC zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Crimestopper Security Products CS-2004DC und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Crimestopper Security Products finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Crimestopper Security Products CS-2004DC zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Crimestopper Security Products CS-2004DC, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Crimestopper Security Products CS-2004DC widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    SERIES II CS-2004TW1 with 2-Way AM Pager/Remote & 1-Way ‘Sidekick’ Remote CS-2004DC II with two 1-Way Remotes INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Security System by Crim estopper Security Products Inc. This booklet contains the information necessary fo r installing, using, and maintaining yo ur 2004[...]

  • Seite 2

    TABLE OF CONTENTS Installation Cautions & Warn ings…….…………………………………… ………………………...………………2 Suggested Component Mounti ng………….…………………………………………………………….…………..3 Wiring……..…………………………………… ………?[...]

  • Seite 3

    CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in t he engine compartment or anywhere they can become entangled with moving parts su ch as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wi re should be routed away from any metal if[...]

  • Seite 4

    WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switc hes are available, install ne w pin switches if desired. GREEN WIRE: (-) DOOR TRIGGER Connect to Negative type door switch es that read gr[...]

  • Seite 5

    WIRING BLACK/WHITE WIRE: (+/-) OUTPUT FROM ON-BOARD 15A RELAY (Term #30, Step #3) Connect this wire to your Auxiliary devi ce or Function. The function of this output depends on the connection of the Gray wire and the polarity of this output ma tches the White/Red wire. (See diagram below) Orange/Black Brown/ Black Red/Black (-) Neg. Domelight Illu[...]

  • Seite 6

    WIRING MINI PLUGS: 2-PIN PLUG (SMALL): LED INDI CATOR (RED FLASHING LIGHT) 2-PIN PLUG (LARGE): PROGRAM /OVERRID E PUSH BUTTON TIP: The Sensor supplied with this system does not require any additional wiring, simply mount the sensor in a suitable location, plug in, and adjust to the desired levels of sensitivity. The Black dial is for Pre-warn level[...]

  • Seite 7

    WIRING BROWN/BLACK WIRE: (-) AUX. OUTP UT #1 OR M.A.P.-Mobile Accessories Protection (Optional) This is a programmable output wire that can operate two different ways: 1. 2. (DEFAULT Operation) A Remote Auxiliary Output that provides a ½ Second (-) Negative pulse when Button #3 is pressed and released to open a pow er trunk or hatch release. Conne[...]

  • Seite 8

    POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Re lay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term. #87: Normally Open [Polarity Input for Unlock rel[...]

  • Seite 9

    POWER DOOR LOCK DIAGRAMS UL REVERSE P OLA RITY DOOR LOCK WIRING + L NEGA TIVE TRIGG ER D OORLOCK WIRING UL L NOT USED UNLO CK WI RE CUT LOCK W IRE CUT FAC T O RY LOCKING RELA YS UL L + A FTERMA RKET MOT OR DOOR LOCK WI RI NG UL L POS ITI VE TRI GGER DOO RLOCK WI RING FUSED +12V + UNLOCK W IRE LOCK W IRE FAC T O RY LOCKING RELA YS X = BLUE GREEN GRA[...]

  • Seite 10

    STARTER DISABLE WIRING STARTER DISABLE PLUG: (3) ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Clo sed or Normally Open Config uration with ON-Board Relay) Note: READ BELOW before connect in g starter disable! Normally OPEN must be programmed to operat e. See pg 13. Normally Closed Starter disable is the standard type used with most alarm systems to[...]

  • Seite 11

    SYSTEM WIRING DIAGRAM IGNITION ST A RTER SWITCH PA R K I N G LIGHTS (+/-) On -Board Relay BA TTER Y - BLACK/WHITE 15A O n- bo ard WHITE/RED GRA Y CUT IGNITION + SWITCH + CAR-JACK ENABLE OUTPUT (-)HOOD/T RUNK TRIGGER S WITCH SIREN (-) ARMED (-)DOOR T RIGGER SW ITCH + DOOR T RIGGER PIN K VIOLET FUSE POLA RITY SELECT UNLOCK(87) GREEN POLA RITY SELECT [...]

  • Seite 12

    CS-2004TW1 ANTENNA The following diagram pertains to t he CS-2004TW1 two-way paging model only: WINDSHIELD ANTENNA LOCA TIONS CS-2004TW1 Black P lug Blue Plug RECOMMENDED Note Orientation of Black & Blue Pl ugs. Colors must match, or system will not operate! Transceiv er Box CS-2004TW1 Antenna System W indow M ount Antenna 12[...]

  • Seite 13

    OPTION PROGRAMMING Soft.686 You can program each option individually or multiple options in one session. You may start with the lowest option # and continue on to higher options wit hout repeating the steps #1 through 3. To Engage Option Programming: 1. Turn Key to the ON position. 2. Press program / valet button 5 times, after a few seco nds the u[...]

  • Seite 14

    OPTION PROGRAMMING 1. AUTOLOCK WITH IGNITION This option controls whether the doors w ill automatically lock when the ignition is turned on and w ill unlock when the ignition is turned off. 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature. If ON, arming will occur 30 Seco nds after the ignition is turned off and the las[...]

  • Seite 15

    OPTION PROGRAMMING 9. OPEN DOOR/ZONE WARNING (5 or 60 Seconds) This setting changes the delay time in which the alarm system begins t o monitor the Door Zone. This is helpful on vehicles with delayed dome lights. It prevents the alar ms warning chi rps due to extended dome light circuit. 10. DOOR LOCK/UNLOCK PULSE TIME Controls the amount of time ([...]

  • Seite 16

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING TRANSMITTER PROGRAMMING NOTES (Read first!): (1) The CS-2004TW1 will learn up to 4 remotes, any co mbination of special CS-398TW 1-Way or CS-389LED 2- Way pager remotes. (2) The CS-2004DC II will up to 4 CS-404T X remotes. The remote controls for the CS-2004DC II and the CS- 2004TW1 systems ARE NOT inter[...]

  • Seite 17

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING IGN OFF WAIT F O R 4 FL A S H ES PRESS 4 X's FLA SH 2, 3, or 4 X' s IGN OFF PRESS TOGETHER "TW 1" OR SLNT AU X "DC" PRESS LOCK BTN SLNT AUX 17[...]

  • Seite 18

    OPERATION SLNT AUX ARM/ DISARM/ UNLOCK LOCK PA G I N G LED's SILENT/ AUX. 2 ANTENNA FIXED AUX. 1 #1 #2 #3 #4 CS-2004T W1 LE D P AGI NG REMO TE CS-2004DC II / CS-2004TW1 remote controls: SLNT #3 #1 #2 #4 LOCK TRU N K SILENT/ UNLOCK VEHICLE 2 FLA SHLIGH T AU X . # 1 AU X . # 2 AUX CS -2004 DC II CS-2004TW1 TWO-WAY PAGER OPERATION & PAGE TONE[...]

  • Seite 19

    OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and t he starter will be disabled. The red in- dash LED in the vehicle will begin to flash. After a short delay of 10-15 seconds to all[...]

  • Seite 20

    OPERATION SHOCK / IMPACT PROTECTI ON WITH PRE-WARNING Once the system is armed, if a low-level shock to the vehi cle body is detected, the pre-warning sensor activates wi th 5 siren chirps and one light flas h as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle fo r 20 seconds. Adjust the[...]

  • Seite 21

    OPERATION PASSIVE ARMING / PASSI VE LOCK MODES (PROGAMMABLE) If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flas h twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopen ed the countdown w[...]

  • Seite 22

    OPERATION CS-2004TW1 LED TRANSCEIVER (LOW BATTERY WARNING) CR2032 3V Lithium Battery T wist and Remove Battery cover w ith a Coin or Screwdriver Larger "+" Posi tive side of battery faces up CS2004TW1 BA TTER Y REPLACEMENT The CS-2004TW1 LED has a low battery warning system. When the battery voltage is low, the LED pager remote will stop [...]

  • Seite 23

    2-VEHICLE OPERATION: (CS-2004DC II SYSTEM ONLY) 2-Vehicle method (C S-2004DC II SYSTEM ONLY): Your CS-2004DC II remote includes a push-button on the side for 2-car operation. You can only operate a second vehicle with a CS-2004DC II system installed. Your remote must be progra mmed to the second vehicle first. Read the following setup and operation[...]

  • Seite 24

    CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protection a nd must be enabled before us e through Alarm programming options #7 & #12 on page 13. We reco mmend this mode should only be used in serious situations. When the Ignition is on (vehicle is running ), and a door is opened, then closed, the Carjack [...]