Craftsman 917.273631 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Craftsman 917.273631 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Craftsman 917.273631, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Craftsman 917.273631 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Craftsman 917.273631. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Craftsman 917.273631 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Craftsman 917.273631
- Den Namen des Produzenten und das Produktionsjahr des Geräts Craftsman 917.273631
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Craftsman 917.273631
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Craftsman 917.273631 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Craftsman 917.273631 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Craftsman finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Craftsman 917.273631 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Craftsman 917.273631, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Craftsman 917.273631 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Owner's Manual CRAFTSMIIN ° 18.5 HE 42" Mower Electric Start 6 Speed Transaxle Model No. 917.273631 i_] his product has a mow emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual. Read and follow all Safety Rules and instructions before operati[...]

  • Seite 2

    Warranty ................................................. 2 Safety Rules ........................................... 3 Product Specifications ............................ 6 Assembly/Pre-Operation ........................ 8 Operation .............................................. 11 Maintenance Schedule......................... 17 Maintenance .....[...]

  • Seite 3

    mMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death. _IWARNmNG: In order to prevent ac- cidental starting when setting up, trans- porting, adjusting or making repairs, always disconnect spark plug wire and place w[...]

  • Seite 4

    DO: Mow up and down slopes, not across. Remove obstacles such as rocks, tree limbs, etc. Watch for holes, ruts, or bumps. Un- even terrain could overturn the machine. Taft grass can hide obstacles. Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. Follow the manufacturer's recommend- ations for wh[...]

  • Seite 5

    Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers or children even with the blades off. Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing. Never carry children. They may fall off and be seriously injured or interfere with sa[...]

  • Seite 6

    PRODUCT SPECIFICATmONS Gasoline 4.0 Capacity and Unleaded Type: Regular Oil Type SAE 30 (above 32°F) IAPFSG-SL): SAE 5W-30(below 32°F Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: 1 st 1.2 2nd 1.6 3rd 2.4 4th 3.6 5th 4.6 6th 5.9 Reverse: 1.8 Tire Pressure: Front:[...]

  • Seite 7

    Mower Leveling Wrench Bubble Level ) Keys (2) Keys (1) Oil Drain Tube For Future Use Slope Sheet Video Cassette "'t[...]

  • Seite 8

    Your new tractor has been assembled at the factory. Review the video cassette before you begin. When right or left hand is mentioned in this manual, it means when you are in the oper- ating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON 1. Cut along dotted lines on all four pan- els of carton. Remove end pa[...]

  • Seite 9

    6. Start the engine. After engine has started, move throttle control to idle position. 7. Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear. 8. Slowly release clutch/brake pedal and slowly drive tractor off skid. 9. Apply brake to stop tractor, set park- ing brake and place gearshift lever in[...]

  • Seite 10

    CHECK TIRE PRESSURE The tires on your tractor were overin- fiated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual. CHECK DECK LEVELNESS For best cutting results, mower hous- ing should be properly lev[...]

  • Seite 11

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I'-,I REVERSE NEUTRAL HIGH LOW CHOKE FAST G G ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE OVER TEMP FUEL OIL PRESSURE LIGHT ATTACHMENT ATTACHMENT CLUTCH ENGAGED CLUTCH DISENGAGED FREE WHEEL (Automatic M[...]

  • Seite 12

    KNOW YOUR TRACTOR READ THINS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATmNG YOUR TRACTOR Compare the illustrationswith your tractor to familiarizeyourself with the locations of various controls and adjustments. Save this manual for future reference. Th rottle/Choke Control Hourmeter ignition Switch iht Switch Position Attachment Clutch Lever[...]

  • Seite 13

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOUR TRACTOR TO SET PAR[...]

  • Seite 14

    For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in pro[...]

  • Seite 15

    TOWING CARTS AND OTHER ATTACH- rvIENTS Tow only the attachments that are recom- mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heaw of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. BEFORE STARTING THE ENG[...]

  • Seite 16

    COLD WEATHER STARTING ( 50 ° F and below) 6. When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme- diately move the throttle control to the fast position. Engine warm-up may take from several seconds to several minutes (the colder the temperature, the longer t[...]

  • Seite 17

    F,LL ,, DATES AS COMPLETE ...... REGULAR SERV,OE f y4 yA TS ERV'C E DATES Check Brake Operation _1_ t_ Check Tire Pressure Check Operator Presence and T Interlock Systems If R Check for Loose Fasteners If I_s If A Sharpen/Replace Mower Blades li#13 C Lubrication Chart tf If 0 Check Battery Level 1_4 a Clean Battery and Terminals _ If i,,'[...]

  • Seite 18

    TRACTOR Always observe safety rutes when per- forming any maintenance. BRAKE OPERATmON If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TmRES , Maintain proper air pressure in all tires (Se[...]

  • Seite 19

    BATT E RY Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life. Keep battery and terminals clean. Keep battery bolts tight. Keep small vent holes open. Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on you[...]

  • Seite 20

    ENGmNE OraL FmLTER Replacethe engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR FmLTER Your engine will not run properly using a dirty air filter. Replace pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every sea[...]

  • Seite 21

    Clean engine, battery, seat, finish, etc. of all foreign matter. Keep finished surfaces and wheels free of all gasoline, oil, etc. Protect painted surfaces with auto- motive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis- sion are covered to keep water out. Water in engine o[...]

  • Seite 22

    TO LEVEL MOWER HOUSmNG Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or undednflated, you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT WITH BUBBLE LEVEL NOTE: If necessary, check side-to-[...]

  • Seite 23

    To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal num- ber of turns. The two front links must remain equal in length. When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nut "F" against trunnion on both front links[...]

  • Seite 24

    TO REPLACE MOTmON DRmVE BELT Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. Remove mower (See "TO REMOVE MOWER" in this section of manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers[...]

  • Seite 25

    TO START ENGINE WiTH A WEAK BAT- TERY ,_kWARNmNG: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this man[...]

  • Seite 26

    Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet. TO ADJUST THROTTLE CONTROL The throttle control has[...]

  • Seite 27

    Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _I, CAUTmON: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tractor f[...]

  • Seite 28

    TROUBLESHOOTmNG CHART: See appropriate section in marluam unmess directed to Sears service center Hard to start Engine wiii not turn over Engine clicks but wiii not start CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7 Water in fuel. 8. Loose or dama[...]

  • Seite 29

    TROUBLESHOOTmNG CHART: See appropriate section in manuam unmess directed to Sears service center CAUSE CORRECTmON 1. 1. Cutting too much grass/too fast. 2. Throttle in "CHOKE" position. 3. Build=up of grass, leaves and trash under mower. 4. Dirty air filter. 5. Low oil level/dirty oil. 6. Faulty spark plug. 7. Dirty fuel filter. 8. Stale [...]

  • Seite 30

    TROUBLESHOOTmNG CHART: See appropriate section in manuam unmess directed to Sears service center Mower blades wiii not rotate PROBLEM CAUSE CORRECTmON 1. Remove obstruction. Poor grass discharge Headlight(s) not working (if so equipped) Battery wiii not charge Engine "backfires" when turning engine "OFF" 1. Obstruction in clutch[...]

  • Seite 31

    SCHEMATmC TRACTOR o o MODEL NUMBER 917.273631 SOLENOID I AMMETER (OPTIONAL) _ED FUSE STARTER I I C G I BLACK WHITE I ] f 1 ............... A 1 ©---'---_, '- BLACK I I LJ I _kJ I _ S H() ........ ' F I ELECTRIC CLUTCH i , H • I -_L A2r-/ f_ _/ VLUI_,n/Dn_B.[- 2 i ) _. I I I ........... _ (PEDAL UP) "_'--_'_ i E I I[...]

  • Seite 32

    ELECTRICAL TRACTOR -- MODEL NUMBER 917.273631 12 / I 41 22 / j 21 I ] 26 40 i f / 16 ] I- ..... I 8O ! / /! / / ! ,, / / ....... i i i i / 12 32[...]

  • Seite 33

    ELECTRmCAL TRACTOR o o MODEL NUMBER 917.273631 KEY PART NO, NO, DESCRiPTiON 1 163465 Battery 2 74760412 Bolt, Hex 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt, Battery, Front 1/4-20 x 7-1/2 11 150109 Holddown, Battery, Front 12 145769 Nut, Push, Nylon, Battery, Front 1/4 16 176138 Switch, Interlock 21 175688 Harness, Light 22 4152J Bulb Light [...]

  • Seite 34

    TRACTOR o o MODEL NUMBER 917.273631 CHASSmS AND ENCLOSURES 90 209 31 209"_ / 54 F209 ./- 20 59 209 /_ 209 206 chassis-stealth,stlt 21 60 74 209 38 60 3; >209 .._ 209 _166 209 34[...]

  • Seite 35

    TRACTOR o o MODEL NUMBER 917.273631 CHASSmS AND ENCLOSURES KEY PART NO. NO. DESCRiPTiON 1 174619 Chassis 2 176554 Drawbar 9 161566X428 Dash 10 72140608 Bolt RDND SQNK 3/8-16 x 1 11 167203 Panel, Dash, LN 13 188702X010 Panel, Dash, RH 14 17490608 Screw Thdrol 3/8-16 x 1/2 17 175260X615 Hood Assembly 20 162026 Plate Battery 26 STD541437 Locknut, Nex,[...]

  • Seite 36

    TRACTOR - - MODEL NUMBER 917.273631 GROUND DRIVE 22 26 27 drive-fender, stlt 34 36[...]

  • Seite 37

    TRACTOR ° ° MODEL NUMBER 917.273631 GROUND DRmVE KEY PART KEY PART NO+ NO+ DESCRIPTION NO+ NO+ 1 TransaxIe Dana D4360-180 56 17060620 (See Breakdown) 57 160855 2 146682 Spring, Return, Brake 59 169691 3 123666X Pulley, Transaxle 61 17120614 4 12000028 Ring, Retainer 62 123533X 5 121520X Strap, Torque 63 175414 6 17000512 Screw 5/16-18 x 3/4 65 8 [...]

  • Seite 38

    STEERmNG TRACTOR o o MODEL NUMBER 917.273631 / : L _ 38 _72 / / 88 J /, J 68 67 67 / 67 13 65 94 34 4O 43 / / / / /_J / 8 steering stealth prem 7 38[...]

  • Seite 39

    STEERmNG TRACTOR o o MODEL NUMBER 917.273631 KEY PART NO. NO. DESCRiPTiON 1 159944X428 Wheel Steering 2 184706 Axle Asm 3 169840 Spindle Asm LH 4 169839 Spindle Asm RH 5 6266H Bearing Race Thrust Harden 6 121748X Washer 25/32 x 1-5/8 x 16 Ga= 8 12000029 Ring Klip #t5304-75 10 175121 Link Drag 11 STD551137 Washer Lock Hvy HIcl Spr 3/8 12 73940800 Nu[...]

  • Seite 40

    ENGINE TRACTOR o o MODEL NUMBER 917.273631 78 33 112 29 OPTIONAL EQUIPMENT Spark Arrester 81 38 14 23 72 13 4 engine-bs.lcyl 51 4O[...]

  • Seite 41

    ENGINE TRACTOR o o MODEL NUMBER 917.273631 KEY PART NO. NO. DESCRiPTiON 1 176636X505 Control ThrottIe 2 171875 Screw Hwhd Hi-Lo #13-16 x 3/4 3 Engine, Briggs Mode! 31P777-0348-E1 (See Breakdown) 4 137352 Muffler 13 165291 Muffler Gasket 14 148456 Tube Drain oiI 23 169837 Shie!d Heat 29 137180 Kit Spark Arrestor (Flat Scrn) 31 179022 Tank Fuel 4.0 R[...]

  • Seite 42

    TRACTOR °° MODEL NUMBER 917.273631 SEAT ASSEMBLY 13 17 12 18 seat It.knob 14 I i I i I i I i I 2 i I i I KEY PART NO. NO. DESCRIPTION 1 180598 Seat 2 180166 Bracket Pivot Seat 3 STD523710 Bolt Fin Hex 3/8-16 unc x 1 4 19131610 Washer 13/32 x 1 x 10 Ga= 5 145006 Clip Pushqn 6 STD541437 Nut Hex w/Ins. 3/8-16 unc 7 124181X Spring Seat Cprsn 8 1[...]

  • Seite 43

    DECALS 18 TRACTOR o o MODEL NUMBER 917.273631 11 16 3 13 21 4 11 21 10 24 2O 7 6 15 26 12 1 KEY PART NO. NO. 1 187407 2 138047 3 186242 DecaI 4 186243 Decal 5 160396 Decal 6 146046 Decai 7 179128 Decal 9 191053 Decal 10 156439 Decal 11 189088 Decal 12 172331 DecaI 13 133644 Decal 15 187408 Decal DESCRIPTION Reflector, LH Decal Battery, Diehard, Sea[...]

  • Seite 44

    TRACTOR o o MODEL NUMBER 917.273631 UFT ASSEMBLY 41 38 40 11 13 4 6 1/ 6 5 19 13 32 13 19 20 • 20 44[...]

  • Seite 45

    TRACTOR -- MODEL NUMBER 917.273631 UFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 179504 PIunger Assembiy 2 159476 Shaft Assembly, Lift 3 178981 Pin, Groove 4 12000002 E-Ring 5 19211621 Washer 21/32 x 1 x21Ga. 6 120183X Bearing, NyIon 7 175830 Grip, Handle, Fluted 11 139865 Link, Lift, L.H. 12 139866 Link, Lift, R.H. 13 STD624008 Retainer Spring 15 17[...]

  • Seite 46

    TRACTOR o o MODEL NUMBER 917.273631 MOWER DECK _ ""_ 40 159 _i 132 91 t _184 59 117 11 34 92__ 92 4 149 5 6 19F 21 140 - , 138 2 16 14 18 13 102 F 21 _5 _134 29 116 21 2 / 23 24 _,_ 6 28 " 27 42 D,elec.t-path.adjwl.stlt 3 46[...]

  • Seite 47

    TRACTOR o o MODEL NUMBER 917.273631 MOWER DECK KEY PART KEY PART NO. NO. DESCRiPTiON NO. NO. 1 182032 Mower Housing 68 174883 2 STD533107 Bolt 92 STD541437 3 138017 Bracket Assembly, Sway Bar, Fr. 101 136420 4 165460 Bracket Sway Bar 38/42" 102 71081010 5 STD624008 Retainer Spring 103 19061216 6 178024 Bar Sway Deck 104 STD551110 8 850857 Bolt[...]

  • Seite 48

    TRACTOR ° ° MODEL NUMBER 917.273631 DANA TRANSA×LE==MODEL NUMBER 4360 EMD 20 21 22 26 27 36 tt_ 9 52 53 54 25 32 57 42 4-3,', 59 56 i5 45 46 47 48 49 50 59 62 7O 63 6¢ / 69 60 6768 23 6 48[...]

  • Seite 49

    TRACTOR o o MODEL NUMBER 917.273631 DANA TRANSAXLE==MODEL NUMBER 4360 EMD KEY PART KEY PART NO. NO. DESCRmPTmON NO. NO. DESCRiPTiON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2o 21 22 23 24 25 26 27 28 29 3o 31 32 33 34 35 36 37 38 39 4o 190972 Housing, Upper 41 105928X 2274J Screw, Tapping, 1/4-20 X .734 42 190986 190973 Ball, Detent 43 13439[...]

  • Seite 50

    TRACTOR ° ° MODEL NUMBER 917.273631 BRmGGS & STRATTON ENGmNE=MODEL NUMBER 31P777,TYPE NUMBER 0348=E1 718 358 ENGINE GASKET SET 8680 8_1_ 146 '_ I 741_ 12 524 617 0 842<:3 943 O 1270 _7591 1027 / I 1019 LABEL KIT II I 1330 REPAIR MANUAL 305A _ 1058 OWNER'S MANUAL I I 1036 EMISSION LABEL I _ _ I [ 1329 REPLACEMENT ENGINE ] 750&[...]

  • Seite 51

    TRACTOR ° ° MODEL NUMBER 917.273631 BRIGGS & STRATTON ENGINE=MODEL NUMBER 31P777,TYPE NUMBER 0348=E1 238 g5 1022 1034 6170 914 1095 VALVE GASKET BET 868 _'_ 1022 _] 131 --10_ • _ _-1o6 lo91 105 276@ 1127L4 _ 127 (_ 601 1119_ 947 918 977 CARBURETOR1370GASKET276 _._SET 160/1 93_ 95 _ 104%-CA R B U R E TO R6_ 4A_KIT-087 105 _ 137_ 276@ f-[...]

  • Seite 52

    TRACTOR o o MODEL NUMBER 917.273631 BRmGGS & STRATTON ENGmNE=MODEL NUMBER 31P777,TYPE NUMBER 0348=E1 KEY PART KEY PART NO. NO. DESCRiPTiON NO. NO. DESCRmPTmON 1 697174 Cylinder Assembly 108 690464 Valve-Choke (Manual Choke) 2 399265 Kit-Bushing/Sea! 108A 692344 Valve-Choke (Choke A Matic) (MagnetoSide) 117 694352 © Jet-Main (Standard) 3 391086[...]

  • Seite 53

    TRACTOR o o MODEL NUMBER 917.273631 BRmGGS & STRATTON ENGmNE=MODEL NUMBER 31P777, TYPE NUMBER 0348=E1 KEY PART KEY PART NO. NO. DESCRiPTiON NO. NO. DESCRmPTmON 383 89838 Wrench-Spark Plug 868 690968 385 694476 Screw (Fuel Pump) 914 690960 385A 690297 Screw (Fuel Pump) 918 697091 387 697090 Pump-Fuel 943 690589 404 691691 Washer (Governor Crank)[...]

  • Seite 54

    54[...]

  • Seite 55

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION L_ ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. _b ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme [...]

  • Seite 56

    iiiiiiiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii _ iiiiiiiiiiiiiiiiiii [...]