Craftsman 917.27206 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Craftsman 917.27206 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Craftsman 917.27206, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Craftsman 917.27206 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Craftsman 917.27206. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Craftsman 917.27206 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Craftsman 917.27206
- Den Namen des Produzenten und das Produktionsjahr des Geräts Craftsman 917.27206
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Craftsman 917.27206
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Craftsman 917.27206 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Craftsman 917.27206 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Craftsman finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Craftsman 917.27206 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Craftsman 917.27206, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Craftsman 917.27206 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Owner's Manual JCRAFTSMAN'J 16.0 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No. 917.272060 • Safety • Assembly • Operation • Maintenance • Repair Parts This product has a low emiSsion engine which operates differently from previously built engines, Before you start the engine, read and understand this Owner&ap[...]

  • Seite 2

    Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ............................................ 11 Maintenance ....................................... 18 Maintenance[...]

  • Seite 3

    IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safely instructions could result in serious injury or death. I. GENERAL OPERATION II. SLOPE OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow respon[...]

  • Seite 4

    III. CHILDREN Tragicaccidents can occur if the operator is not alert to the presence of children, Children are often attractedto the machine and the mowingactivity. Never assume that children will remain where you last saw them. • Keep childrenout of the mowing area and underthe watchful care of another responsible adult. • Be alert and tum mac[...]

  • Seite 5

    • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn o[...]

  • Seite 6

    PRODUCT SPECIFICATIONS SASOLINE 1.25 GALLONS CAPACITY UNLEADED _.ND TYPE: REGULAR DILTYPE SAE 10W30{above 32°F) _,PI-SF-SJ): SAE 5W-30 (below 32°F) ; OIL CAPACITY: W/FILTER: 4,0 PINTS W/OFILTER: 3.5 PINTS SPARK PLUG: CHAMPION RC12YC SAP: .040") VALVE CLEARANCE: NOT ADJUSTABLE GROUND FORWARD: 5.5 SPEED(MPH): REVERSE: 2.4 ]'IRE FRONT: 14 [...]

  • Seite 7

    Steering Wheel Insert _1_(1) Hex Bolt 3/8-16 x 1 Steerin! _ Boot Steering Wheel (1) Lock washer 3/8 (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 (1) Locknut 5/16-18 =_ Steedng Wheel Adapter t Stx_:nd;gn Shaft at (1)Washer 17/32 x 1-3/16 x 12 Gauge _(1) Knob Slope Sheet Keys € (2) Keys Video Cassette For Future Use[...]

  • Seite 8

    Your new tractor has been assembled atthe factory with exception ofthose parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardwareyou assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Reviewthe video cassettebefore you begin. TOOLS REQUI[...]

  • Seite 9

    Battery Door Terminal INSTALL SEAT Adjustseat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packingand set aside for assemblyof seat to tractor. 2. Pivotseat upward and remove from the cardboardpacking. Remove the cardboard packingand discard. 3. Place seat on seat pan so head of shoulderbol[...]

  • Seite 10

    INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of muicher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck. 4. Hook rear latch into hole on back of mower deck. ,_CAUTION: Do not remove deflector shield fro[...]

  • Seite 11

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING ENGINE ON ENGINE OFF REVERSE FORWARD FAST SLOW @ ixl FUEL CHOKE OIL PRESSURE LIGHTS ON OVER TEMP LIGHT MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT LOCKED _r_'m R N H L c®)_ I ATTACHMENT REVERSE[...]

  • Seite 12

    KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of variouscontrols and adjustments. Save this manual for future reference. Attachment Clutch Ammeter Ignition Switch Light Switch Lift J Lever Plunger Throttle/Choke Atta[...]

  • Seite 13

    The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repaim. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOWTO USEYOURTRACTOR TO SET PARKING[...]

  • Seite 14

    • For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relativelyhigh;the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are propedy adjusted when they are slightly off the ground when moweris at the desired cutting height in operatingposition. Gauge wheels then keep the deck in prob[...]

  • Seite 15

    NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). TOWING CARTS AND OTHER ATTACH- MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of you[...]

  • Seite 16

    • The attachments and grounddrive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING ( 50° F and below) 7. When engine starts, allow engine to run with the throttlecontrol in the choke position until the engine runs roughly, [...]

  • Seite 17

    MOWINGTIPS • Mower should be properly leveled for best mowingperformance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the rightof the tracto[...]

  • Seite 18

    MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES CheCk Brake O_Uorl Check Tire pro'_u_ V _ Check Operator Presence and T Intelt_k Systems II_ CheCk I0¢ LoOSe Fasteners ll_ I_z I_ A Sherper_Replsce Mower Bktde= I1_, T Check Battery Level R G lean Battery and Terminals I1_ V r Check Transaxle Cooling li_ Adjust B[...]

  • Seite 19

    TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See &q[...]

  • Seite 20

    BA'I-FERY Your tractor has a battery charging system which is sufficient fornormal use. How- ever, periodic charging ofthe battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equip[...]

  • Seite 21

    8. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished. Oil Drain Valve Closed and Locked Position Cap Drain Tube CLEAN AIR S[...]

  • Seite 22

    3. Apply a thin coating of new engine oil to the rubber gasket on replacement oil filter. 4. Install replacement oil filter on filter adapter. Turn oil filter clockwise until rubber gasket contacts the filter adapter, then tighten filter an addi- tional 1/2 tum. 5. Fill crankcase with new oil (See "TO CHANGE ENGINE OIL" in this section of[...]

  • Seite 23

    _CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key "OFF" and remove key. 5. Make sure the blades and all moving parts have completely sto[...]

  • Seite 24

    SIDE-TO-SIDE ADJUSTMENT • Raise mower to itshighest position. • At the midpoint of both sides of mower, measure height from bottom edge of mowerto ground. Distance "A"on both sides of mowershould be the same or within 1/4" of each other. • If adjustment is necessary, make adjustment on one side of moweronly. • To raise one si[...]

  • Seite 25

    BELT INSTALLATION - 4. Install new belt in reverse order of removal. 5. Make sure belt is in all pulley grooves and inside all belt guides. 6. Install mower in reverse order of removal instructions. TO ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than s[...]

  • Seite 26

    2. Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep. 3. Tighten adjustment bolt securely. 4. Start engine and test. 5. If tractor still creeps, repeat above steps until satisfied. Motion Control Neutral Lock Gate Lever TRANSMISSION REMOVAL/REPLACE- MENT Should your transmission require removal for service or repl[...]

  • Seite 27

    REPLACING BATTERY _CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding, 1. Lift seat pan to raised position [...]

  • Seite 28

    TO ADJUST CARBURETOR Thecarburetor has beenpreset at the factory and adjustment should notbe necessary, However, minor adjus_ant may be required to compensate fordifferences in fuel, temperature, altitude orload.If the cadouretor doesneed adjustment, proceed as follows: In general, turning the adjuslJng nsedles in (clockwise) decreases the supply o[...]

  • Seite 29

    immediately prepare your tractor for storage at the end of the season or if the 'ractor will not be used for 30 days or ,'nore, CAUTION: Never store the tractor Nith gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR Remove mower from tract[...]

  • Seite 30

    TROUBLESHOOTING CHART PROBLEM Will not start Hard to start Engine will not turn over CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter, 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9. Carburetor out of adjustment. 10. Enginevalves out of adjustment. 1. D[...]

  • Seite 31

    "ROUBLESHOOTING CHART CORRECTION PROBLEM Loss of power continued) Excessive vibration Englnecontinues to run when operator leaves seat with attachment clutch engaged Poorcut-uneven Mower blades will not rotate i CAUSE 3. Build-up of grass, leaves and trash under mower. 4. Dirty air filter. i 5. Low oil level/dirty oil. 6. Faulty spark plug. 7.[...]

  • Seite 32

    TROUBLESHOOTING CHART PROBLEM CAUSE Poor grass 1. Engine speed too slow. discharge 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressure, 6. Wom, bent or loose blade. 7. Buildup of grass, leaves and trash under mower. 8. Mower ddve belt worn. 9. Blades improperly installed. 10.Improper blades used. 11 .Clo[...]

  • Seite 33

    TRACTOR - - MODEL NUMBER 917.272060 SCHEMATIC IGNITION SWITCH BATtERy SOLENOID R_O (_ _ FUSE ' i (OPTIONAL) w_l_ i _ 1_ a_c_ CLUTCH / BRAKE r I (PEDAL UP) , ...... 4 ATYMENT CLUTCH i _-_ - (CLUTCH OFF) ;8-5 .... _, FUE_ SH_-OF_ '- -_ ...... SOLENOIO SEAT SWITCH (NOT OCCUPIED) _ OPERATOR PRESENCE RELAY #1 86; i OPERATOR ESENCE RELAY #2 SPA[...]

  • Seite 34

    TRACTOR - - MODEL NUMBER 917.272060 ELECTRICAL 24 41 / t 34[...]

  • Seite 35

    TRACTOR -- MODEL NUMBER 917.272060 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 12 Volt 28 Amp 2 74760412 Bolt, Hex Head 1/4-20 uoc x 3/4 8 156417 Case, Battery Mech Hinge 16 161343 Switch, interlock N Opn/N Opn 21 166182 Harness, Light Socket (Includes 4152J) 22 4152J Bu;b, Light 24 4799J Cable, Battery, 6 Gauge, Red, 11" 25 14614[...]

  • Seite 36

    TRACTOR -- MODEL NUMBER 917.272060 CHASSIS AND ENCLOSURES 3 74 44 I 2O6[...]

  • Seite 37

    TRACTOR - - MODEL NUMBER 917.272060 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 169830 Chassis Stamping 2 169061 Dmwber 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carrlage 3/8-16xl 11 155927 Panel, Dash, L.H. 12 145660 Clip TInnetman Gttlle P/L 13 172107X010 Panel, Dash, R.H, 17 144963X558[...]

  • Seite 38

    TRACTOR -- MODEL NUMBER 917.272060 GROUND DRIVE[...]

  • Seite 39

    TRACTOR -- MODEL NUMBER 917.272060 GROUND DRIVE KEY PART KEY NO, NO. DESCRIPTION NO. 1 ...... Transaxle (See BreakdOwn) _5 Hydro Gr 314-0510 66 8 165866 Rod Shift Fender Adjust 70 10 ST[To61210 PInCotter 1/8xl CAD 71 14 10040400 Washer LOCkH W Helical 72 15 74490544 BOlt Hex FLGHD 5/16-18 x Gr 5 73 16 STD541431 Nut Lock Hex W/Ins. 5/16-18 Unc 74 19[...]

  • Seite 40

    TRACTOR -- MODEL NUMBER 917.272060 STEERING ASSEMBLY ,- L 11 4o 2 _29 40[...]

  • Seite 41

    TRACTOR -- MODEL NUMBER 917.272060 STEERING ASSEMBLY KEY PART NO: NO. DESCRIPTION 1 139768 SteedngWheel 2 154427 Axle Assembly STMP Dropped STL 3 169840 Spindle Assembly, LH. 4 169839 Spindle Assembly, R.H. 5 6266H Beadng, Race, Thrust, Hardened 6 121748X Washer 23/32 x 1-5/8 x 16 Gauge 7 19272016 Washer 27/32 x 1-1/4 x 16 Gauge 8 12000029 Ring, Kl[...]

  • Seite 42

    TRACTOR -- MODEL NUMBER 917.272060 ENGINE ! 38 1o! 31 /: _ 33 29 OPTIONAL EQUIPMENT Spark Arrester 8o i , :i i 42[...]

  • Seite 43

    TRACTOR - - MODEL NUMBER 917.272060 ENGINE KEY PART NO. NO. DESCRIPTION 1 170548 Contrbl, Throffie 2 17720410 Screw, Hex Head, Thread Cuffing 1/4-20 x 5/8 3 ...... Engine, (See Breakdown) Kobler ModelNo. CV460-26509 4 159420 Muffler 13 12-041-03 Gasket Kohier 14 148456 Tube Drain Oil Easy 16 ST[To51237 Washer 23 169837 Shield Sm/Dbr Guard 29 137180[...]

  • Seite 44

    TRACTOR -- MODEL NUMBER 917.272060 SEAT ASSEMBLY 8 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 140123 Seat 13 121248X Bushing, Snap 140551 Bracket, Pivot, Seat 14 72050412 Bo_tl Cardage 1/4-20 x %1/2 71110616 Bo_t 15 134300 Spacer, Split .28 x .88 19131610 Washer 13/32 x I x 10Gauge 16 12t250X Spdng 145006 C[...]

  • Seite 45

    TRACTOR - - MODEL NUMBER 917.272060 DECALS 10 20 '12 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 156811 Decal, Oper. instr. 13 177336 Decal, Lower Dash 2 177368 Decal, HP Engine 14 160396 Decal, V-Belt Schema_c 3 171698 Decal, Hood, R.H. 16 138047 Decal. Battery Diehard 4 171699 Decal, Hood, LH. 20 149516 Decal, Battery Dngr/Pon [...]

  • Seite 46

    TRACTOR -- MODEL NUMBER 917.272060 LIFT ASSEMBLY 13 3 2 6 5 4 19 13 ---,-_ _ 31 32 13 19 2O 46[...]

  • Seite 47

    TRACTOR - - MODEL NUMBER 917.272060 LIFT ASSEMBLY KEY PART NO. NO, DESCRIPTION 1 159460 [_If{ Lever Inner Wire Assembly 2 159471 Shaft ASSembly, Lilt 3 105767X Pin, Groove 4 120000(_ E-F_ng 5 19211621 Washer 21/32 x 1 x 21 Gauge 6 120183X Beadng, Nylon 7 125631X Grip, Handle, Fluted 8 122365X Button, Plunger, Red 11 139865 Link, Uft, L.H. 12 139866[...]

  • Seite 48

    TRACTOR -- MODEL NUMBER 917.272060 MOWER DECK 157 _ _/,_ 67 151 . ' 183 ISS _37 159-_ "44 _1505 .._ 105 106 102 103 102/_' 34 >21 119 5 6 118 16 1 48[...]

  • Seite 49

    TRACTOR - - MODEL NUMBER 917.272060 MOWER DECK KEY PART NO. NO, DESCRIPTION 1 165892 Mower Deck Assembly, 42" 2 STD533107 Belt 3 138017 Bracket Assembly,Sway Bar, Front 4 165460 Bracket Sway Bar 38/42" ack 5 STD_4C(_ Retsiner Spdng 6 130832 Arm, Suspension, Rear 8 850_57 Bolt, Hex 3/8-24 x 1.25 Gr. 8 9 STD551137 Washer, Lock 10 140296 WaS[...]

  • Seite 50

    81 77 79 / 73 _, 82 17 32 93 58 48 124 107 o 0 °i mO a | oO m o , f- zl- 0_=_. °_ I0 0[...]

  • Seite 51

    TRACTOR - - MODEL NUMBER 917.272060 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO, NO, DESCRIPTION 59 1704G6 Rotor, Brake 1 170_51 Main Housing, Assembly 60 142883 Brake PUCk 2 170352 Sibe Housing, Aseembly 61 142881 Puck Plate 3 170_53 Center Section, Assembly 62 142887 Brake Act_a_t_g Pk_ 4 170354 Swashpl[...]

  • Seite 52

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEAD, VALVE AND BREATHER I I j" 18 19 CRAHKCASEJ 1 19 18 10 52[...]

  • Seite 53

    TRACTOR o- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEADNALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO. DESCR_TION NO. NO. DESCRIP_ON 25-351-01-S • 12-755-94-S 1 Lifter, valve (2) 2 Kit, cylinder head (Includes 3-17, Gaskets 12 041 01-S (Qty. 2),12 041 02- S, & 12 041 03-S 3 Rod, push (2 4 Gasket[...]

  • Seite 54

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 IGNITIONIELECTRICAL BLOWER HOUSING AND BAFFLES I I 3 4 s V AiR INTAKE I _'-s I- m7 54[...]

  • Seite 55

    TRACTOR - - MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 IGNITION/ELECTRICAL KEY PART NO. NO, DESCRIPTION BLOWER HOUSING & BAFFLES KEY PART NO. NO, DESCRIPTION 1 12-086-14-S Screw, hex. flange M10x1.5x46 1 M-545010-S Screw, hex. flange 2 12-468-03-S Washer, plain 3/8' M5x0.8xl0 (4) 3 24-162-03-S Screen, grass[...]

  • Seite 56

    TRAC_R -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, _PE NUMBER 26509 STARTING SYSTEM 1 I m 0 tF 8 !]-- ENGINE CONTROLS I 1 11 2 4 OiL PAN I LUBRICATION I 1 ?--1o -_3 tl S q _ 20 7" t6 O/16 1C2..', 56[...]

  • Seite 57

    TRACTOR - - MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 STARTING SYSTEM ENGINE CONTROLS KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 8) 3 12-755o39-S Kit, drive end 4 12-227o03-S Cap, drive end 5 12-170-04-S Armature 6 12-755-38-S Kit, drive parts 7 12-243-O4-S Cap, commutator end 8 12-086-20-S Screw, [...]

  • Seite 58

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CRANKSHAFT I EXHAUSTJ --1 FUELSYSTEM I ,7 II _ jll I /7 6 --lo 58[...]

  • Seite 59

    TRACTOR -- MODEL NUMBER 917.272060 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 FUEL SYSTEM KEY PART NO. NO. DESCRIPTION 1 M-641060-S Nut, hex. flange M6xl.O (2) 2 X-22-11-S Washer, lock 1/4" 3 M-629116-S Stud M6x1.0x116 (2) 4 12-853-115-S Kit, carburetor w/gasket (Includes 5,6,7 qty 1) 5 12-041-02-S Gasket, air cleaner 6 12-653-115 Car[...]

  • Seite 60

    60[...]

  • Seite 61

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL d A Operate your Tractor up and down the face of slopes (not i i AUk grseter thon15"), never acrons the face. Maketumsgradu- I | _ ally to prevent tipping or loss of control, Exercise extreme I / caution when changing direction on slopes. ( I![...]

  • Seite 62

    62[...]

  • Seite 63

    63[...]

  • Seite 64

    Get it fixed, at your home or ours! For repair of major brand appliances In your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM A.ytime, Say or night (1-80o469-4e63) www.sesrB.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Seers Parts & Rep[...]