Billion BiPAC 7100SV Bedienungsanleitung

BIPAC 7100SV VoIP ADSL Modem/Router with Single Ethernet Port User Manual[...]

[...]

i Table of Contents Chapter 1 ............................................................................... 1 I NTRODUCTION ................................................................................................... 1 1.1 An Overview of BIPAC 7100SV .................................................................................. 1 1.2 P[...]

Billion BIPAC 7100SV VoIP ADSL Router ii 3.4.3.4.3 Upgrade ............................................................................................................................. 45 3.4.3.4.4 Factory Setting .................................................................................................................. 45 3.4.3.4.5 Restart [...]

1 Chapter 1 Introduction 1.1 An Overview of BIPAC 7100SV BIPAC 7100SV VoIP ADSL Modem/Router provides a hi gh-speed Ethernet port for high-speed Internet browsing. It can support d ownstream transmission rate s of up to 8Mbps and upstream tran smission rates of up to 1024Kbps. It is compliant with Multi-Mo de standa rd (ANSI T1.413, Issue 2; G.dmt [...]

Billion BIPAC 7100SV VoIP ADSL Router 2 between the PSTN world and the IP world acting as a residential gateway, eventually providing Internet Telephony capability. Cost savings and ease of developing and integrating new services motivate most of the interest in Internet telephony. Internet telephony integrates a variety of service s provided by th[...]

Chapter 1 Introduction 3  Dynamic Domain Name System (DDNS): The Dynamic DNS service allows you to alias a dynami c IP address to a static hostname. This dynamic IP address is the WAN IP addr ess. For example, to use the service, you must first apply an accou nt from this free Web server http://www.dyndns.org/ . There are more than 5 DD NS serve[...]

Billion BIPAC 7100SV VoIP ADSL Router 4 1.4 BIPAC 7100SV Application[...]

5 Chapter 2 Using Billion VoIP ADSL Modem/Router 2.1 Cautions for Using Billion VoIP ADSL Modem/Router Do not place the router under high humidity and high temperat ure. Do not use the same power source for the dev i ce w ith other equipment. Do not open or repair the case y ourself. If the device is too hot, turn off the po wer immediately and hav[...]

Billion BIPAC 7100SV VoIP ADSL Router 6 2.3 The Rear Ports LED Meaning Power Switch A Power ON/OFF switch Power Jack Connect the supplied power adapter to this jack. Reset Press it to restore the factory default setting back. VoIP Connect RJ-11 cable to this port when connecting to an analog phone set. LAN (RJ-45 connector) Connect the supplied Eth[...]

7 Chapter 3 Configuration BIPAC 7100SV can be configured with your Web browse r. The web browser is includ ed as a standard application in following op eration systems, UNIX, Linux, Mac OS, Windo ws 95/98/NT/2000/Me/XP, etc. The product provides a very easy and us er-friendly in terface for co nfiguration. 3.1 Before Configuration This section desc[...]

Billion BIPAC 7100SV VoIP ADSL Router 8 3. In the Local Area Connection Status window, c lick Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Chapter 3 Configuration 9 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and Dial-up Connections . 2. Double-click Local [...]

Billion BIPAC 7100SV VoIP ADSL Router 10 3. In the Local Area Connection Status window, c lick Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Chapter 3 Configuration 11 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 95/98/ME 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and choose the Configuration tab. 2. Select[...]

Billion BIPAC 7100SV VoIP ADSL Router 12 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click OK to finish the configuration.[...]

Chapter 3 Configuration 13 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties .[...]

Billion BIPAC 7100SV VoIP ADSL Router 14 3. Select the Obtain an IP address from a DHCP server radio button and click OK . 3.2 Factory Default Settings Before you configure this device, you n eed to know the followi ng default settings. 1. Web Configuration Password: There are two leve ls of password protection, Administrator Level and User Lev el [...]

Chapter 3 Configuration 15 3.2.1 Password The default username and password are admin an d password respectively. If you ever forget the pass w ord to log in, you may press the RESET button up to 2 seconds to restore the fa ctory default settings. 3.2.2 LAN and WAN Port Addresses The parameters of LAN and WAN port s are pre-set in the factory. The [...]

Billion BIPAC 7100SV VoIP ADSL Router 16 IPoA VPI/VCI, VC-based/LLC-based multip lexing, IP address, Subnet mask, Gateway address, and Domain Name S ystem (DNS) IP address (it is fixed IP address). 3.4 Configuring with Web Browser The ADSL Modem/Router can be configured with your Web browser. The web brow ser is included as a standard application i[...]

Chapter 3 Configuration 17 At the configuration homepage, the l eft navigation p ane where bookmarks are provided links you directly to the desired setup page, including:  Status (ADSL Status, LAN Status, PPP Status, Learn ed MAC Table, Routin g Table, System Log, Security Log)  Quick Start  Configuration (WAN, LAN, VoIP, System, Firewa ll[...]

Billion BIPAC 7100SV VoIP ADSL Router 18 3.4.1.1 Status – ADSL Status Displays the status of your ADSL conn ection. It will refresh every two seconds. 3.4.1.1.1 ADSL Status – WAN Status[...]

Chapter 3 Configuration 19 3.4.1.1.2 ADSL Status – ATM Status 3.4.1.2 Status – LAN Status Displays the status of your Local Area Network (LAN) connection.[...]

Billion BIPAC 7100SV VoIP ADSL Router 20 3.4.1.2.1 LAN Status – TCP Status 3.4.1.3 Status- PPP Status Displays the status of your PPP connect ion. It will refresh every ten seconds.[...]

Chapter 3 Configuration 21 3.4.1.4 Status- Learned MAC Table Aging Timeout: Enter the time period for the router to memori ze MAC addresses.[...]

Billion BIPAC 7100SV VoIP ADSL Router 22 3.4.1.5 Routing Table Display the current routing paths of BIPAC 7100SV. 3.4.1.6 System Log Display the system logs cumulated t ill the present time. You can trace t he historical information through this function.[...]

Chapter 3 Configuration 23 3.4.1.7 Security Logs Display the information of security logs. If hacker attacks your sever, he will be isolated by the firewall function and the router w ill record related information. Hence, you know where the hacker comes from.[...]

Billion BIPAC 7100SV VoIP ADSL Router 24 3.4.2 Quick Start If you use this device to access the Internet through the ISP, this web page is enough fo r you to config ure this router to access the Internet and enable VoIP se rvice without a problem. 3.4.2.1 ADSL Quick Start Please check Chapter 3.3 ( Information from the ISP) , then enter the proper [...]

Chapter 3 Configuration 25 3.4.3 Configuration When you click this item, you get follo wing sub-items to configure BIPAC 7100SV. LAN, WAN, Firewall, System, VPN, Virtual Server, Advanced and Help 3.4.3.1 WAN The screens below contain settings fo r the WAN interface toward Internet. Select Adapter[...]

Billion BIPAC 7100SV VoIP ADSL Router 26 Select the item of PVCs you want to configure. Then, press the Submit button.[...]

Chapter 3 Configuration 27 Virtual Circuit Virtual Circuit: Enable/Disable the settings of this VC. Bridge: If you set this device to be bridge mode, select Enable; if not, please select Di sabl e. IGMP: You can Enable or Disable this function. Encapsulation: There are eleven ways ─ PPPoE VC-Mux, PPPoE LLC, PPPoE None, PPPoA VC-Mux, PPPoA LLC, 14[...]

Billion BIPAC 7100SV VoIP ADSL Router 28 Internet. You have to check with your ISP about which way is adopted.VPI: Consult the telephone company to get the Virtual Path Identifie r (VPI) number. The default value is 0. ATM VPI: Consult the telephone company to get the Virtual Path Identifier (VPI) nu mber. The default value is 0. VCI: Consult the t[...]

Chapter 3 Configuration 29 indicate its MRU and will be accepted. The actual MT U of the PPP connection will be set to the smaller one of MTU and the peer’s MRU. The default value is 1492. MSS: Maximum Segment Size is the largest size of data that TCP will send in a single IP pa cket. When a connection is established between LAN client and a hos [...]

Billion BIPAC 7100SV VoIP ADSL Router 30 remember to specify a static IP address, subnet Mask, and DNS se tting for each of your local computers. Be careful not to assign the same IP address to different com puters. DHCP address pool selection: Auto or User Def ined. If select the AUTO, router will assign an IP address back to PC’s IP request. If[...]

Chapter 3 Configuration 31 3.4.3.3.1 General Configuration This screen contains some basi c settings for the VoIP Module. SIP: Enable/Disable to use SIP (Session Initiation Protocol) as VoIP call signali ng protocol. You need to enable SIP in order to make or receive SIP calls. SIP Registration: Enable/Disable to register a SIP account in the SIP s[...]

Billion BIPAC 7100SV VoIP ADSL Router 32 This screen contains regist ration -related settings for getting VoIP services from SIP s ervice provider. Service Provider List: This section all ows you to select the se rvice provider. When the selection i s done, respective parameters below are automat ically displ ayed. New Service Provider: You can add[...]

Chapter 3 Configuration 33 Login Account List: Select the correct accounts that you want to u se. New Account Name: If you want to modify or add ne w account and need to enter new account name. UserID: Enter your registration ID given by SIP Registrar Serve r Password: Enter the Password for authentication with the registrar AuthUserID: same as Use[...]

Billion BIPAC 7100SV VoIP ADSL Router 34 Speed Dial: The VoIP ADSL Router provides 10 entries from 0 to 9. When you dial “#0” mapping to entry 0 in the phone book. Abstract Description: indicate the purpose or useful information f or this entry. Remote UserID: Enter the UserID you want to contact. Refer UserID to VoIP -> C onfiguration ->[...]

Chapter 3 Configuration 35 If your friend Greg gives you an IP address "192.246. 56.56" only, then you can enter the Pho ne book as: Remote UserID: (leave blank, don't fill anything) IP Address / Domain: 192.246.56.56 3.4.3.3.3 Dial Plan This section allows you to set-up rules f or your dialing actions. Working Service Provider: This[...]

Billion BIPAC 7100SV VoIP ADSL Router 36 Rule Number: You can e stablish multiple rules for the dial pla n. Enter the rule number you would like t o edit or delete. Prefix: This is the actual dial plan prefix string to be st ored. In case of no prefix , the string NULL must be stored. Prefix Timer: This is the Inter-Digit timer value in m illisecon[...]

Chapter 3 Configuration 37 CallForwarding: CallForwarding Unconditi onally : VoIP device will forward all incomi ng call to the forwarding number. CallForwarding On Busy: VoIP device will forward a ll incoming call to the forwarding number when user is already on the phon e talking to someone else. CallForwarding On No Answer: VoIP device will forw[...]

Billion BIPAC 7100SV VoIP ADSL Router 38 Configure Caller ID info: Modulation: This is Caller ID Modulation (Bell 202.V 23). You can sele ct between CID_BELL202 and CID_V23. Delay: Delay , in milliseconds , between the end of the first ring and beginni ng of the CID transmission. FSK AMP 0: FSK (Frequency-Shift Keying) is a method of transmitting d[...]

Chapter 3 Configuration 39 Configure VAD: VAD (Voice Activity Detection) is a function to detect voice activity during one conversation. It is to efficiently utilize the bandwi dth by not transmitting “empty” voice packets when both sides remain silent. In the meantime, a comfort noi se could be gen erate d (occupied little bandwidth). Disable [...]

Billion BIPAC 7100SV VoIP ADSL Router 40 Note: Codec priority is selected u sing a drop-down box. If two codec types are assigne d the same priority, then the priority is assi gned in t he order as G711U > G711A > G 729 in the decreasing order of priority. For example, if the user selects 1, 2, 2, for G711U, G711A, and G729A respectively, the[...]

Chapter 3 Configuration 41 RingBack Tone: Defined by six fields, Frequency1, Frequency2 , On Time1, Off Time1, On Time2, Off Time2. Frequency is given in hertz. Time is given in milliseconds. CallWaiting Tone: Defined by six fields, Frequen cy1, Frequency 2, On Time1, Off Time1, On Time2, Of f Time2. Frequency is given in hertz . Time is given in m[...]

Billion BIPAC 7100SV VoIP ADSL Router 42 Predial Timeout: indicate the time period thro ugh which the dial tone is heard o nce the phone is lifted off the hook. At the end of this period, if no digits have been pressed, VoIP device will start playing fast-busy tone. Alert Timeout: indicate the time for which VoIP device will pl ay the ring when an [...]

Chapter 3 Configuration 43 3.4.3.4.1 Password In factory setting, the default password is password , and that for user is also password. You can change the default password to ensure that someone cannot adjust your setting s without your permission. Every time you change your password, please record the passwo rd an d kee p it at a safe place. Plea[...]

Billion BIPAC 7100SV VoIP ADSL Router 44 3.4.3.4.2 Time Zone BIPAC 7100SV does not have a real time clock on board ; instead, it uses the simple network time protocol (SNTP) to get the current time from the S NTP server in outside network. Please choose your local time zone and click Submit. Y ou will get the correct time information after you real[...]

Chapter 3 Configuration 45 3.4.3.4.3 Upgrade To upgrade the firmware of BIPAC 7100SV, you should download or co py the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. Wh en the procedure is completed, BIPAC 7100SV will reset automati c[...]

Billion BIPAC 7100SV VoIP ADSL Router 46 3.4.3.4.5 Restart In case the router stops responding correctly or in som e other way stops functioning, you can perform the restart. Your setting won’t be changed. Performi ng th e restart, click on the Submit button.[...]

Chapter 3 Configuration 47 3.4.3.5 Firewall User can decide to enable this firewall function incl uding Packet Filter, Block Ha cker Attack, and Block WAN request features for better security control or not. But be noted, it wa stes net work processor computation power. The performance will be lower about 10% to 15%. More firewall feature s will be[...]

Billion BIPAC 7100SV VoIP ADSL Router 48  Outgoing  Incoming: Determine whether the rule is for o utg oing packets or for incoming packets. Active: Choose “Ye s” to enable the rule, or choose “No” to disable the rule. Packet Type: Specify the packet type (TCP, UDP, ICMP or any) that the rule will be applied to. Select TCP if you want [...]

Chapter 3 Configuration 49 3.4.3.5.2 MAC Filtering Enable Bridge Filtering: Check Yes to enable this function or check No to disable. Src MAC: Enter the source MAC addre ss. Dest MAC: Enter the destination MAC address. Typ e: Enter the Ethernet type.  Block  For w ard: Check Block if you want to block requests fr om the source MAC a ddress se[...]

Billion BIPAC 7100SV VoIP ADSL Router 50 - Smurf Attack (ICMP Echo with x.x.x.0 or x.x.x.255) - Snork Attack - UDP port loop-back - TCP NULL scan 3.4.3.5.4 Block WAN Request Check “Enable” if you want to exclude outside PING request from reaching on this router.[...]

Chapter 3 Configuration 51 3.4.3.6 Virtual Server Being a natural Internet firewall, the ADSL Router pr otects your netw ork from being ac cessed by outs ide users. When it needs to allow out side users to access internal servers, e.g. We b server, FTP server, E- mail server or News server, this produ ct can act as a virtual server. You can set up [...]

Billion BIPAC 7100SV VoIP ADSL Router 52 For example, if you set the Public Port n umber 21 (FTP) to be mapped to the IP Addres s 192.168.1.100, then all the ftp requests from outsid e users will be forwarded t o the local server with IP address of 192.168.1.100. Public Port (from) & Port (To): Enter the publi c port number & range you want[...]

Chapter 3 Configuration 53 3.4.3.7.2 DNS A Domain Name System (DNS) co ntains a mappi ng table for domain name and IP addres s. In the Internet, every host has a uniqu e and friendly name such as www.yahoo. com and IP address. The IP address is so hard to rem ember that you may just enter the friendl y name www.yahoo.com and then the DNS will conve[...]

Billion BIPAC 7100SV VoIP ADSL Router 54 3.4.3.7.3 Dynamic DNS With Dynamic DNS service, a domain name can be trans lated into a dynamic IP address, which i s often issued by ISP for dial-up se rvice. A local server, su ch as Web server, Email server o r FTP server, can then be easily accessed without kno wing the changing IP address.[...]

Chapter 3 Configuration 55 Check the “Enable” button to access the Dynamic DNS service. You may si gn up Dynami c DNS service at http://www.dyndns.org T and there you can al so register domain names. Host: Enter one domain na me you have registered. User Name: Enter the usernam e used for si gn-up. Password: Enter the password used for sign-up.[...]

Billion BIPAC 7100SV VoIP ADSL Router 56 Session Name: Enter the desired se ssi on name. User’s IP: Allows the user to assign the IP address to map the co rresponding NAT/NAPT sessions. Session Name status will be displayed at the middle of this page to show t he corresponding Session Name with its IP address. Click Session Name Configuration, th[...]

Chapter 3 Configuration 57 3.4.3.7.5 RIP RIP: Default is Disabled . Border Gateway: Default is Enabled . Supply Interval  seconds: The default value is 30 second s. Expire Timeout  seconds: The def ault value is 1 80 seconds. Garbage Timeout  seconds: The default value is 120 second s.[...]

Billion BIPAC 7100SV VoIP ADSL Router 58 3.4.3.7.6 Static Route If you have another router with a LAN-to-LAN connecti on, you may create a static routing on the route r that is the gateway to Internet. Add: Click this button to add a new static routing. When you click thi s button, the next figure appea rs.[...]

Chapter 3 Configuration 59 Delete: Check the item you want to delete. Then, cli ck the “Delete” button. Destination / Subnet Mask / Ga teway Address: Fill in these fields require d by this Static Routing function. 3.4.3.7.7 MISC Configuration HTTP server access: Default at Res tricted . HTTP server port: Default at 80 . FTP server: Default at E[...]

Billion BIPAC 7100SV VoIP ADSL Router 60 3.4.3.7.8 Diagnostic Test As soon as you enter the test pro gram, all tests will run automatically to diagnose the co nnection status of the device. Checking LAN Connectio n Testing Ethernet LAN connec tion This test passes if the Ethernet LA N interface is working p ro perly. Checking ADSL Connection Testin[...]

Chapter 3 Configuration 61 This test sends ATM OAM F5 Segm ent loop back reque st cells to the central office equi pments through your DSL connection. This test will pass if response cell is received. Si nce your service pr ovider might not support this test, your DSL modem coul d still work even if this test fails. If this test fails consistently [...]

3.4.4 Save Config Click the Submit button to write settings to flash. Then, the system will reboot for changes to take effe ct. 62[...]

63 Chapter 4 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADSL Router Problem Corrective Action None[...]

64 APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshoo ting section in the User’s Manual . If you cannot resolve the problem with the Troubles hooting chapter, please contact the dealer where you purch ased this product. Contact Billion AUSTRALIA http://www.billion.com.au/ ©2004 Billion El[...]