Audiovox AA-RS30CS Bedienungsanleitung

Model AA-RS30CS Installation Manual This Unit is Intended for Installation in V ehicles with 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel with T rue T ach Reference and Automatic T ransmissions Only . Kit Contents AARS-30CS Control Module (2) - 3 Button Anti Code Grabbing Transmitters 3 Channel Code Learning Receiver External Sup[...]

The AA-RS30CS is Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow p[...]

3 Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the switch using the nut, star washer , and on/of f face plate. It is suggested that the switch be oriented to allow the on position to be up toward the driver and the off position to be down or away from the driver . Rou[...]

SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. 4 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key i[...]

WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self tapping screw and ring terminal. 5 BLACK w/WHITE Tracer Wire: Control Switch The Black w/[...]

connect the Brown w/Black trace wire to the output of the brake light switch. If the brake light switch in the vehicle switches ground, do not use the Brown w/Black wire; see Grey w/Black tracer wire. 6 YELLOW w/BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: YOU MUST DISCONNECT THE IGNITION INPUT OF THE ALARM FROM ANY OTHER WIRE THAT IT [...]

LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below , a relay will be required. The Light Bl[...]

8 DARK GREEN/ORANGE Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start unit learns [...]

9 The Green wire of the two pin harness provides a ground pulse during the disarming sequence, or pulsed ground unlock output. Connect the Green wire to the low current ground signal wire from the factory door unlock switch to the factory door unlock relay . See Below For Wiring Detail. 3 Wire Positive Switched Door Locks: In this application, the [...]

10 disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the AA-RS30CS is used to unlock the doors. Black w/Light Green T race Wire: Pulsed Ground Output After Start The Black w/Light Green Trace wire will provide a 1 second 300ma pulsed ground output after the vehicle is[...]

11 Entry Illumination Detail Green w/Black T race Wire: 300mA Latched Channel 3 Output The Green w/Black T race wire supplies a 300mA switched output whenever channel three of the receiver is ac - cessed. Pressing the pre-programmed transmitter button(s) will access channel three and will remain active, for up to 8 seconds, as long as the transmitt[...]

12 NOTE: 1. When selecting Diesel operation, (Feature Nine), over gasoline, the only change is to the ignition circuits. When Diesel is selected, the ignition circuits will power up 10 seconds before the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle is a instant start di[...]

13 1 Flash 10 or 15 Minute Run Timer Expired 2 Flashes Low or No Tach Signal (RPM) 3 Flashes Positive Or Negative Shutdown Wire Activated 4 Flashes Control Switch Moved to Off Position 5 Flashes RF shutdown, Remote signal received, or manual start trigger wire reactivated. 6 Flashes High RPM Signal Received NOTE: 7 Flashes when attempting to remote[...]

14 TESTING YOUR INST ALLA TION: W ARNING!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOOD PIN SAFETY SHUT[...]

15 necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. W ARNING ! REMEMBER TO R[...]

16 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear . AU[...]

17 METHOD 2 G. Connect terminal 87 of the relay to the Chime Module side of the previously cut wire in step D. H. Connect terminal 85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B. NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the ca[...]

18 COMPLETING THE INST ALLA TION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: 1. If not done so already , place the red rubber handle cover over the handle of the control switch for ease of identification. This will allow your customer to distinguish the Remote Start con[...]

19 WIRING DIAGRAM[...]

© 2000 Audiovox Electronics Corp. , Hauppauge N.Y. 11788 128-5818[...]