AT&T 9351 Bedienungsanleitung

900 MHz Cor dless T elephone/ Ans wering System 9351 Please also read Part 1 — Important Product Infor mation USER ’ S MANU AL Pa r t 2 DELETE A T&T and the globe symbol are registered trademar ks of A T&T Corp. licensed to Adv anced American T elephones. REVISED 1/1/01 9351_book_2ATT 1/1/01 3:33 PM Page ii[...]

© 2000 Advanced Amer ican T elephones. All rights reser ved. Printed in China. 850004375 Issue 2A T&T 12/00 9351_book_2ATT 1/1/01 3:33 PM Page iii[...]

INST ALLA TION . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Befor e Y ou Install .......................... 2 T a ble/Desk Installation ................. 4 W all Installation ............................ 5 TELEPHONE OPERA TION . . . . . . . . . . . . . 7 Mak e or Answ er a Call .................. 7 End a Call ..............................[...]

Befor e Y ou Install 1 Choose a location for the base near an electrical outlet and a telephone jack. This phone requires a modular telephone jac k and a standard electrical outlet (110v A C) not controlled by a wall switc h. 2 Install the handset battery. b) Plug batter y pack connector into handset. d) Replace cover by sliding it up into place. a[...]

INST ALL A TION 3 3 Attach the belt clip to the cordless handset (optional) . T o attach To r emove 9351_book_2ATT 1/1/01 3:33 PM Page 3[...]

INST ALLA TION 4 Use only the pow er cord supplied with this product. If you need a replacement, call 1 800 222-3111. 3 Char ge the handset battery. Place the handset in the base. Charge the battery for at least 24 hours the first time. After the first charge, the batter y is typically fully charg ed overnight. 4 Check for dial tone. After the batt[...]

INST ALLA TION 5 W all Installation 1 Position the wall mount adapter on the base. 2 Connect the telephone line cord. 3 Connect the power cord. The ANSWER ON/OFF light g oes on, and CL f lashes in the Message Windo w . Use only the pow er cord supplied with this product. If you need a replacement, call 1 800 222-3111. Align tabs on wall mount adapt[...]

INST ALLA TION 6 4 Mount the base on the wall. 5 Follow Steps 3–5 in “T able/Desk Installation.” a) Align holes on base with mounting studs on wall jack. b) Place power cord as shown, so it hangs straight down between base and wall. c) Pull base down on mounting studs until it locks into place. 9351_book_2ATT 1/1/01 3:33 PM Page 6[...]

TELEPHONE OPERA TION 7 End a Call Place handset in base — OR — Press O . Exit pr ogramming. Cancel a page. Handset V olume Adjust volume of what you hear through the handset. Mak e or Answ er a Call Lift handset from base — OR — Press P and w ait f or light to go on steadil y . Flash/ Call W aiting Access special telephone company subscribe[...]

TELEPHONE OPERA TION 8 P age/Handset Locator Pr ess once to page the handset f or up to one minute; press twice to cancel. Indicates handset is in base Indicates spar e battery is installed Indicates base is connected to AC power Flashes when a call is coming in; on steadily when any phone on this line is in use Spar e battery compartment 9351_book[...]

TELEPHONE OPERA TION 9 T emporar y T one Dialing If you hav e dial pulse (rotar y) ser vice, you can chang e from dial pulse to touch tone dialing during a call by pressing * . This is useful if you need to send touch tone signals f or access to telephone banking or long-distance ser vices. 1 Dial the number . 2 Press * . Buttons pressed after this[...]

Headset Jack Y ou can use this telephone hands-free when you install a 2.5 mm headset (A T&T SKU# 24099), purchased separatel y . Plug the headset into the jack located on the right side of the handset (under the small rubber f lap). Do not force the connection, but make sure the plug fits securel y . Opera ting Range This cordless telephone op[...]

TELEPHONE MEMOR Y 11 Stor e a P ause in a Memory Number Pr ess to store a two-second pause in the dialing sequence. Eac h press adds another two- second pause and counts as one digit. Stor e Memory Numbers 1 Mak e sure the handset is off. 2 Press G . The PHONE light blinks. 3 Press the number button (0–9) where you want to stor e the telephone nu[...]

ANSWERING SY STEM OPERA TION A T THE BASE 12 Audib le Indica tors This system gives y ou voice prompts f or feature oper ations and voice confirmations when you press a button or complete an oper ation. About Mailbo xes This answ ering system has three voice mailboxes. Caller s using a touch tone phone can select the mailbox in which their messag e[...]

ANSWERING SYSTEM OPERA TION A T THE BASE 13 Recor d Y our Announcement NOTE: If you hav e assigned dif fer ent mailbo xes to dif fer ent people, be sur e to tell callers in your announcement to pr ess # 1 , # 2 , or # 3 to leav e a message in the appr opriate mailbox. 1 Press U until y ou hear “Set Outgoing Message. ” 2 Press / . After y ou hea[...]

Answ ering System F eature Setup Y ou can set up one featur e at a time, or you can set up a featur e and then move on to set up another f eature. 1 Make sure the ans wering system is on. 2 Press and release U until y ou hear the system announce the featur e you want to set. Ref er to the “Feature Summar y” below for a description of the featur[...]

ANSWERING SYSTEM OPERA TION A T THE BASE 15 Listen T o, Sa v e & Delete Messages The system automatically sav es your messages until y ou delete them, and can store approximately 15 min utes of messa ges, memos, and announcements (up to a maximum of 99 messages). After playing a messag e, the system announces the day and time it was received. W[...]

Call Scr eening/Intercept 1 Mak e sure the ans wering system is on, and set the message playback volume control abov e level 1 so you can hear the caller’ s messa ge. 2 If you decide to take the call, press P on the handset. 3 If y ou pick up an e xtension phone dur ing the announcement and the announcement does not stop right away , press and re[...]

ANSWERING SYSTEM OPERA TION A T T OUCH T ONE PHONE 17 Connect with the Answ ering System Y ou can access many f eatures of this system remotely fr om a touch tone phone. 1 Dial your telephone number . 2 When the system answ er s, press # , then enter your Remote Access Code (preset to 19). The system beeps twice. 3 Within tw o seconds, enter a remo[...]

Remote Access Commands Function: Command: Play messages in Press # , then the appropriate mailbox a mailbox n umber ( 1 , 2 , or 3 ). The system pla ys new messages. If there are no new messages, the system plays old messages. Repeat a message Press # 4 while message is pla ying; each press bac ks up another message. Skip a message Press # 6 while [...]

BA TTERIES 19 Char ging the Handset Ba tter y P ack This batter y should remain charg ed up to six days with the ringer turned on and up to twelv e days with the ringer off. A fully charg ed batter y provides an av erage talk time of about six hours. The batter y pack needs charging when: • A new battery is installed in the handset. • The phone[...]

20 Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cov er downward. 2 Lift out the old battery pack and disconnect. 3 Align the two holes in the new battery pack’s plug with the socket pins, and snap the plug into place. Place the battery pack in the compartme[...]

BA TTERIES 21 Spar e Batter y Char ger This phone is equipped with a built-in spare batter y charg er in the base unit. The spare batter y charger allows y ou to always hav e a charg ed batter y available should the handset batter y charg e become low . T o install the spare battery pack (purc hased separatel y , Replacement Batter y #3301, A T&[...]

IN C ASE OF DIFFICUL TY 22 If you hav e dif ficulty operating this phone, tr y the suggestions below . For Customer Service, visit our website at www .telephones.att.com or call 1 800 222–3111. Please retain your r eceipt as your pr oof of pur chase . If the phone doesn’ t work a t all, check these items first: • Mak e sure the A C adapter is[...]

IN C ASE OF DIFFICUL TY 23 If y ou hear noise or interfer ence when using the phone: • Mak e sure the base antenna is full y upr ight. • Y ou may be out of r ange. Mov e closer to the base. • Press and release C to c hange to another of the 30 c hannels available. If noise is exceptionall y loud, move closer to the base bef ore changing c han[...]

IN C ASE OF DIFFICUL TY 24 If y ou ha ve difficulty hearing messages: Chec k the v olume setting. If the system does not answ er after the correct number of rings: • Mak e sure that the ANSWER ON/OFF light on the base is on. If it is off, press o . • If T oll Saver is on, the number of r ings chang es to two when you hav e new messages w aiting[...]