AirLive WN-2600HD Bedienungsanleitung

AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 1 AirLiv e P oE-2600HD / W N - 2 6 0 0 H D 802.3af P oE H.264 2.0 Me ga-Pixel PT IP Camera /W ir eless N H.264 2.0 Me ga-Pixel PT IP Camera Use r ’ s Manual[...]

Copyright and Disclaimer AirLive PoE-2600HD/ WN-2600HD User ’ s Manual i Owner's Record The model and serial numbers are located at t he bottom of device. Record these numbers in the spaces provided below . Refer to t hese numbers whenever you call upon your dealer regarding this product. Model No. ____________________ Serial No. ___________[...]

Copyright and Discl aimer AirLive PoE-2600HD/ WN-2600HD User ’ s Manual ii Notice: The changes or modifications not expressly approved by the p art y responsible for compliance could void the user ’ s authority to operate the equipment. For customers in the U.S.A. This equipment has been tested and found to comp ly with the limits for a digit a[...]

Copyright and Disclaimer AirLive PoE-2600HD/ WN-2600HD User ’ s Manual iii IMPOR T ANT NOTE: T o comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt ed. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user ’s authority to op[...]

T able of Cont ents i AirLive PoE-2600HD/ WN-2600HD User ’ s Manual T able of Content s 1. Introduction .................................................................................................................3 1.1 Overview ..............................................................................................................3 1.2 [...]

T able of Co ntents AirLive PoE-2600HD/ WN-2600HD User ’ s Manual ii 4.3.3 Maintenance ............................................................................................59 4.4 V ideo: Configure Profile .....................................................................................62 4.4.1 Common ...................................[...]

1. Introduction 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 1 1. Introduction 1.1 Overview This user ’s guide explains how to operate this camera from a computer . User should read this manual completely and carefully before you operate the device. This camera is an inexpensive and fully scalable surveillance device. Because the Network Cam[...]

1. Introduction AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4 The device is accessible via the LAN or Inter net connection. Connect your device directly to a local area network or xDSL modem, and with Microsof t® Internet Explorer you get instant, on demand video streams. Within minutes you can set up the device to capture a video sequence to [...]

1. Introduction 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 1.2 Package Content s User can find the following items in the package: 1. This camera is the main element of the product. 2. Camera mount kit and pads. 3. Detachable WLAN antenna (for WN-2600HD WLAN model only). 4. Power adapter dedicates 12V DC elec tric power output to Network Cam[...]

1. Introduction AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 6 1.3 Physical Description Front V iew z High-light LEDs These LEDs are high power LED type. It’ s very useful for low-lux environment to provide supplementary light source for image sensor . z Lens & focus ring User could use this ring to adjust focus manually . z Microphone The[...]

1. Introduction 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Rear V iew z Audio Output Jack Audio-out Jack allows this device to output audio or alerting sound. z DC Power Jack The input power is 12VDC. Note that supply the power to the Camera with the power adapter included in package. Otherwise, the improper power adapter may damage the unit[...]

1. Introduction AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 8 1. Insert the paper clip or other tool and press and hold the button down continuously . 2. Hold it at least 5 seconds and release the tool. Then the device has been restored to default settings and reboot again. Note : Restoring the factory default setting will lose the all previous[...]

1. Introduction 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 1.4 Mounting the Camera Ceiling Mount 1. Fix the camera to L-type bracket with the two supplied screws 2. Fix the bracket and camera to the ceili ng using two holly wall anchors and screws[...]

1. Introduction AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 10 W all Mount 1. Fix the L-type bracket to the wall using two holly wall anchors and screws 2. Fix the camera to L-type bracket with the two supplied screws[...]

1. Introduction 1 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 1.5 Inst all the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket loca ted on the camera’ s rear and attach it to the network. Ethernet Cable 2. Connect the external pow er supply to Camera Connect the attached power adapt er to [...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 12 2 2. Prep aration 2.1 Search and Set up by IPWizard II When you installed the Camera on a LAN envi ronment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discover y . Here is the way to execute IPWizard II to discover Camera’ s IP address and set up relate[...]

2. Preparation 1 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual When launch the IPWizard II, a searching wi ndow will pop up. IPWizard II is starting to search Network Cameras on the LAN. The existed devices will be listed as below .[...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 14 2.1.2 View If IPWizard II finds network devices, Vie w button will be available. Please select the device you want to view and click the Vie w button. Then you could see the video from camera directly . Furthermore you could double click the left button of mouse to link to the networ[...]

2. Preparation 1 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 2.1.3 LAN In case you want to change the IP related para meters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below .[...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 16 Y ou could modify the relative setti ngs of the selected device. Click “ << ” button will quit the LAN setting procedure and click “ >> ” button will move to next page as below .[...]

2. Preparation 1 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual In case, you do not want to change user name and/or p assword, then just click “ Submit ” button to perform your setting accordingly . Click “ << ” button will go back to previous page. If you like to change username and/or password of the device, just click the check [...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 18 2.1.4 Wireless (WN-2600HD Only) In case you want to change the IP related para meters of wireless interface, please select the device you want to configure and click the WIRELESS button. Relative settings will be carried out as above.[...]

2. Preparation 1 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Click SSID to select your wireless AP or router and key in WEP or WP A key . Click >> to next step:[...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 20 Make sure wireless setting and then submit it.[...]

2. Preparation 2 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Click OK to confirm these parameters, then IPWizard II will start to configure this camera with specified information.[...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 22 Once this step finished, IPWizard II will prompt you to unplug the Ethernet cable to activate wireless access. Then IPWizard II will prompt y ou to test wireless setting or finish wireless procedure as below .[...]

2. Preparation 2 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 2.2 UPnP of W indows® XP , Vist a or 7 UPnP™ is short for Universal Plug and Play , which is a networking architecture that provides compatibility am ong networking equipment, sof tware, and peripherals. This device is an UPnP enabled device. If the op erating system, Windows XP [...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 24 However , if your NA T router support s UPnP feature, it can be very easy to achieve NA T traversal automatically . T o do this, enable the NA T -traversal feature, which will attempt to automatically configure the router to allow access to the camera. Installing the device with an U[...]

2. Preparation 2 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 2. T ype in your login name and password under “USERNAME” and “P ASSWORD” textbox. For the first time use ( default value), input the User Name: admin Password: airlive That’ s, type in “ admin ” on the “USERNAME” and “ airlive ” on the “P ASSWORD”. Click ?[...]

2. Preparation AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 26 4. After the ActiveX control was installed and ran, the first ima ge will be displayed. 2.5 Logging in as an User If you log in the Camera as an ordinary User , “Setting” function wil l be not accessible. 2.6 Logging in as an Administrator If you log in the Camera as the Administ[...]

3. Operating the Network Camera 2 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 3 3. Operating the Network Camera S tart-up screen will be as follow no matter an ordinary users or an administrator . ActiveX Control Monitor Image Section Full Screen Monitor Image Section The image shot by the device is shown here. T he date and time are disp lay[...]

3. Operating the Network Camera AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 28 Language The device could provide multiple langua ges to meet customer ’s requirement. 2-W ay Audio The device supports 2-way audio function. Us er can chose to enable or disable this function by toggling the icon below . : Disable audio up loading function. : Enab[...]

3. Operating the Network Camera 2 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Camera direction: Control camera up/down/left/right and home position. z Camera speed: Choose the speed of Pan and T ilt. z Preset: Add/Update the preset positions or go to one of these positions. z T our: Select one of the camera tours. Camera tour is comprised b[...]

3. Operating the Network Camera AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 30 z Digital Zoom Click Digita l Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position.[...]

3. Operating the Network Camera 3 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Snapshot Click Snapshot to activate this fu nction. Pr ess Snap shot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser , the pop-up window to select the save path and file name prefix, select OK to continue. If you[...]

3. Operating the Network Camera AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 32 file name prefix, select OK to continue. After stop recording, list the files, this file is named as V ideo_yyyymmddhhmmss.avi The ASF files can be display by the standard Windows Media Player , but it needs the DixectX 9.0 or later version to be installed. z Vo l u [...]

3. Operating the Network Camera 3 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z About Click About to show this ActiveX information.[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 34 4 4. Administrating the Device System Setting This function is only available for user logged into Camera as administrator . Click on each menu name to display its setting p age. Item Action Network Configure Network settings such as DHCP , DDNS, 3GPP , PPPoE and UPnP C[...]

4. Administrating the Device 3 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.1 Network: Configure Network Settings Use this menu to configure the network to connect the device and the clients. 4.1.1 Network This section provides the menu for connecting the device through Ethernet cable. z MAC address: Displays the Ethernet MAC address of the [...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 36 z IP address, Subnet mask, and Gateway: If you do not select Obtain an IP address aut omatically , then you need to enter these network parameters manually . z Obtain DNS from DHCP: DNS: S tands for Domain Name System. Enable this checked box when a DHCP server is insta[...]

4. Administrating the Device 3 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.1.2 Wireless (WN-2600HD Only) If your device is a wireless model, you could assign the related parameters into wireless setting. Using a wired connection ensures great er secrecy while making these settings. These settings should always be made in the ca mera first a[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 38 z Setting (Easy Inst allation): Provides a 2-step procedure to configure wireless setting: Ste p 1 : Select SSID of wireless r outer or access point (AP).[...]

4. Administrating the Device 3 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Ste p 2 : Key in security key of WEP or WP A. Then click “ OK ” button to activate wireless setting. In case, user wants to configure wireless settings manually , please follow the steps as below: z MAC address: Displays the Ethernet MA C address of the WLAN card. [...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 40 z Ty p e : T o select one of WLAN modes from Infrastructure or Ad-Hoc mode. z Security mode : Shows which type of security the network uses. The device support s three security methods: None WEP WP A_PSK/WP A2_PSK z SSID : This is the name of the wirel ess network the d[...]

4. Administrating the Device 4 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z WP A settings : − WP A Key: Key value of WP A. The device uses a pr e-shared key (PSK) for key management. The pre-shared key can be entered either as Manual hex, as 64 hexadecimal characters, or as a Passphrase, using 8 to 63 ASCII characters. z Obtain IP address [...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 42 A dynamic DNS service is unique because it provides a means of updating your IP address so that your listing will remain cu rrent when your IP address changes. There are several excellent DDNS services available on the Internet. One such service you can use is www .DynD[...]

4. Administrating the Device 4 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z DDNS: T o enable or disable t he DDNS service here. z Server name: Choose the built-in DDNS server . z DDNSHost: The domain name is applied of this device. z User name: The user name is used to log into DDNS. z Password: The password is used to log into DDNS. 4.1.4 P[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 44 z PPPoE: T o enable or disable the PPPoE service here. z User name: T ype the user name for the PPPoE service which is provided by the ISP . z Password: T ype the password for the PPPoE service which is provided by the ISP . z IP address, Subnet mask, and Gateway (read [...]

4. Administrating the Device 4 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.1.5 Streaming R TSP is a streaming control protocol, and a starting point for negotiating transport s such as R TP , multicast and Unicast, and for negot iating codecs. RTSP c an be considered a "remote control" for controlling the media st ream delivered b[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 46 4.1.6 UPnP UPnP is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, sof t ware, and peripherals. This device is an UPnP enabled Network Camera. If your operat ing system is UPnP enabled, the d[...]

4. Administrating the Device 4 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z UPnP: T o enable or disable the UPnP service here. z Friendly Name: Shows the friendly name of this device here. z UPnP NA T T raversal When enabled, the device will attempt to conf igure port mapping in a NA T router on your network, using UPnP™. Note that UPnP™[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 48 4.1.8 IP Filter Y ou can enter dif ferent user ’s IP address which are allowing enter or denying by the device. z IP Filter: T o enable or disable the IP filter function here. z IP Filter Policy: Choose the filter policy where is denying or allowing.[...]

4. Administrating the Device 4 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.1.9 IP Notification In case the IP address is changed, system is abl e to send out an email to alert someone if the function is enabled. z SMTP Notification (e-mail): If enable this function, then the “ Send to “and “ Subject ” fields need to be filled. z Sen[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 50 z TCP Notification: If enable this function, then the “ TCP Server “, “ TCP Port ”, and “ Message ” fields need to be filled. z TCP Server: T ype the server name or the IP address of the TCP server . z TCP Port: Set port number of TCP server . z Message: The[...]

4. Administrating the Device 5 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z URL: T ype the server name or the IP address of the HTTP server . z HTTP Login name: T ype the user name for the HTTP server . z HTTP Login Password: T ype the password for the HTTP server . z Proxy Address: T ype the server name or the IP address of the HTTP Proxy .[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 52 4.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p arameters of the device. 4.2.1 Picture z Rotation: T urn the “Mirror” and “V ertical Flip” On or OFF . The image will be overturned as below .[...]

4. Administrating the Device 5 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z White Balance: Auto: will adjust the white balance automatically . Hold: will hold the white balance. z Exposure Control: Auto: will adjust the inte rnal gain automatically . Hold: will hold the internal gain. z Color Level: Large value will be colorful. z Brightness[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 54 4.2.2 Preset Setting This page provides the edit tool to modify or delete the “Preset Setting” item by item.[...]

4. Administrating the Device 5 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.2.3 Tour Setting Up to 128 positions can be preset, and the ca mera can be programming to move to the preset position sequentially . z T our Name: The group name of the sequence of camera tour . The maximum number of camera tour is 16. z Running: Enable or disable th[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 56 4.3 System: Configure and Maint ain System Use this menu to perform the prin cipal settings of the device. 4.3.1 System z DIPS (Dynamic IP Service): T o enable or disable the DIPS® (D ynamic IP Service) function. z Device ID (for DIPS): It’ s a unique number of each [...]

4. Administrating the Device 5 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual T o use this service, just follow four steps below: (1) Enable DIPS function of the device (2) Check your Device ID fr om this p age. This is a unique number for each device. (3) If your device is behind a NA T router , please configure your device properly . Y ou coul[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 58 z Reload: Click this button; user can refresh the log information of the device. 4.3.2 Date & Time Y ou can setup the device or make it synchroni zed with PC or remote NTP server . Also, you may select your time zone in or der to synchronize time locally . z Server [...]

4. Administrating the Device 5 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.3.3 Maintenance z Hard Factory Default (Include the network setting): Recall the device hard factory default settings. Note that click this button will reset all device’ s parameters to the factory settings (including the IP address). z Factory Default (Except the [...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 60 z Restore Setting: Click the “Browse” button to locate the saved backup file and then click the “ Restore Setting ” button. The settings will be restored to the previous configuration. z Firmware Upgrade: The device supports new firmware upgrade (the so f tware [...]

4. Administrating the Device 6 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 6. The upgrade progress informati on will be di splayed. Once the uploading process completed, the device will reboot the system automatically . 7. Please wait for timer countdown, and then you can use IPWizard II to search the device again. W arning!!! The download fi[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 62 4.4 Video: Configure Profile This device provides 2 modes of video prof ile. The first one is Mega-pixel mode which supports video resolution up to Mega-pixel. Howe ver the maximum frame rate of this mode is up to 15fp s only . The second one is VGA mode which supports [...]

4. Administrating the Device 6 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.4.2 Video Profile z Name: Assign a name to the selected profile. z V ideo T ype: V ideo codec of the se lected video profile. z Resolution: Resolution of the selected video profile. z ROI: Assign the selected profile as a ROI stream or not. z Rate Control: Defines th[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 64 z Max Frame Rate: Defines the targeted frame rate of this profile. For example, set the frame rate to 15 fp s, then the image will be updated for 15 frames per second as possible. User need to set reasonable max frame rate versus video quality under the limited bandwidt[...]

4. Administrating the Device 6 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.5 Audio: Audio Parameters z Audio: T o enable or disable audio function z Mute While PT : Mute the audio while pan and/or tilt motion z Audio Mode: T o select Simplex or Full duplex (2-way audio) mode z Input Gain: T o adjust gain of input audio z Output Gain: T o ad[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 66 4.6 User: Manage User Name, Password and Login Privilege Use this menu to add, update, or remove the usernames and passwords of the Administrator and viewer . z V iewer login: Select “Anonymous” to allow any one vi ewing the video once connected. Otherwise, only use[...]

4. Administrating the Device 6 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.7 E-Mail: Setup E-Mail Configuration Y ou may setup SMTP mail p arameters for furt her operation of Event Schedule. That’ s, if users want to send the alarm message out, it will need to configure parameters here and also add at least one event schedule to enable ev[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 68 z SSL: Enable SSL function or not. z SMTP Authentication: Select the authentication requi red when you send an e-mail. Disable: if no authentication is required when an e-mail is sent. Enable: if authentication is required when an e-mail is sent. z Authentication User n[...]

4. Administrating the Device 6 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Add and Del: T o add or delete the motion windows. User can specify up to 10 Included and/or Excluded windows to monitor the video captur ed by this device. By dragging mouse on the image, you can change the position and size of the selected motion window accordingly[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 70 4.9 Storage: S tatus and Configuration of SD Card This page shows the st atus of attached SD card. Y ou may setup related parameters to manage the attached SD card also. z Enable automatic disk cleanup: Delete old recorded files while the conditions are reached as below[...]

4. Administrating the Device 7 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 4.10 Recording List: Files List Inside the SD Card This page shows the files list information. Us er may play or delete the selected file. 4.11 Event Server: Setup FTP/TCP/HTTP/SAMBA Server Configuration 4.11.1 FTP Server Y ou may setup FTP p arameters for further oper[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 72 z Name: User can specify multiple FTP p aths as wis h. Therefore, user needs to specify a name for each FTP setting. z FTP Server: T ype the server name or the IP address of the FTP ser ver . z T est: Check the FTP server whether this account is available or not. z FTP [...]

4. Administrating the Device 7 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z FTP Path: Set working directory path of FTP server . z FTP Passive Mode: Select passive or active mode connecting to FTP server . 4.11.2 TCP Server In addition to send video file to FTP server , the device also can send event message to specified TCP server . z Name:[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 74 4.11.3 HTTP Server The device also can send event message to specified HTTP server . z Name: User can specify multiple HTTP servers as w ish. Therefore, user needs to specify a name for each HTTP server setti ng. z URL: T ype the server name or the IP address of the HTT[...]

4. Administrating the Device 7 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Proxy Login Password: T ype the password for the HTTP Proxy . z Proxy Port: Set port number of Proxy . 4.11.4 SAMBA Server The device also can send video str eam to specified SAMBA server . z Name: User can specify multiple HTTP servers as w ish. Therefore, user need[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 76 z SAMBA Login Password: T ype the password for the SAMBA server . z SAMBA Path: Set working directory path of SAMBA server . 4.12 Event Schedule: Configure the Event Schedule 4.12.1 Setting This menu is used to specify the schedule of Event or Schedule T r igger and act[...]

4. Administrating the Device 7 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z T ype: Event trigger or Schedule trigger . z Enable T ime: Define the feasible time slot. z T rigger by: Select the triggered sources. z Action: Define the actions once event triggered. Example 1: Send file to FTP server by motion triggered always: 1. Select event tr[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 78 Example 2: Send file to E-Mail server by motion trigger ed from Friday 18:00 to Saturday 06:00 1. Select event trigger . 2. Enable time: start from Friday 18:00 and keep work in 12 hours, so it will stop on Saturday 06:00. 3. T rigger by : Motion Area (Added in Object D[...]

4. Administrating the Device 7 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Example 3: Enable V oice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday . 1. T ype: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Friday , and set start time from 18:00 and keep work in 6 hous. 3. T rigger by : Y[...]

4. Administrating the Device AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 80 4.12.2 Record User can choose the type of record f ile for event or schedule application. z Record File T ype: Choose JPEG , A VI-JPEG , or A VI-H.264 file format. z Record File Prefix: Define the prefix of recorded filename. z JPEG Picture Numbers: Define the picture n[...]

4. Administrating the Device 8 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Post-T rigger Duration: Define the maximum duration of post-alarm. z Max File Size: Define the maximum buf fer size of record file.[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 82 5 5. Appendix Appendix A: Alarm I/O Connector Some features of the Network Camera can be activated by the external sensor that senses physical changes in the area Network Camera is monitoring. These changes can include intrusion detection or certain physical chang e in the monitored are[...]

5. Appendix 8 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Explanation of External I/O Circuit Diagram: z CAUTION! − THE LOW VOL T AGE/CURRENT CIRCUITS AND HIGH VOL T AGE/ CURRE NT CIRCUITS ARE IN THE NETWORK CA MERA CIRCUIT . THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRI NG NOT BY YOURSELF . INCORRECT WIRING COULD DAMAGE NWTWORK CAMERA. YO[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 84 Appendix B: T roubleshooting & Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing hi gh quality images. Where H.264 and MPEG4 are standards fo[...]

5. Appendix 8 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual password for the first time or after facto ry default reset Note that it’ s all case sensitivity . Forgot the username and password Follow the steps below . 1. Restore the factory def ault setting by press pressing and holding down more than 3 seconds on the device. 2. Reconfigure th[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 86 failed support more cameras. Y ou could turn off and on NA T router to clear out of date information inside router . Access this device Cannot access the login page and other web pages of the Network Camera from Internet Explorer • Maybe the IP Address of the Network Camera is already[...]

5. Appendix 8 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual • Some routers reject the global IP address to access the Network Camera on the same LAN. Access with the private IP address and correct port number of Network Camera. • When you use DDNS, you need to set Default Gateway and DNS server address. • If it’ s not working after abov[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 88 outside your LAN. • Make sure that the device isn’t conflicting with any other web server running on your LAN. • Check the configuration of the router settings allow the device to be accessed outside your local LAN. • Check the bandwidth of In ternet connection. If the Internet [...]

5. Appendix 8 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual V ideo quality of the device The focus on the Camera is bad. • The lens is dirty or dust is att ached. Fingerprints, dust, stain, etc. on the lens can degrade the image quality . The color of the image is poor or strange. • Adjust White Balance. • T o insure the images you are vi[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 90 If you want to detect any other devices conf licts with the IP address of Network Camera, also can utilize the PING command but you must disconnect the device from the network first. Appendix D: Bandwid th Estimation The frame rate of video transmitted from the device depends on connect[...]

5. Appendix 9 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Note : Audio streaming also takes bandwidth around 32kbp s. Some xDSL/Cable modem upload speeds could not even reach up to 128 kbps. Thus, you may not be able to receive good quality video while also streaming audio on a 128 kbps or lower connection. Even though the upload speed is mor[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 92 S treaming over UDP , TCP , or HTTP M-JPEG streaming over HTTP (server push) Supports 3GPP mobile surveillance Controllable frame rate and bandwidth Constant and variable bit rate (MPEG4 / H.264) ROI Audio Audio Encoder R TSP: G .71 1 64kbps, G . 726 32kbps, AAC 3GPP: AMR Audio S treami[...]

5. Appendix 9 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Connectors RJ-45 10BaseT/100BaseTX DC power jack 1 alarm input and 1 output Audio out Factory default reset SD card Indication LED T wo-Color LED Illumination LED 12 IR LEDs Operating T emperature 0°C to 40°C (32°F to 104°F) Operating Humidity 20% ~ 80% (non-condensing) Dimension H[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 94 (1) Assign a local/fixed IP address to y our device The device must be assigned a local and fixed IP Address that allows it to be recognized by the router . Manually setup the device with a fixed IP address, for example, 192.168.0.100. (2) Access the Router with Y our Web browser The fo[...]

5. Appendix 9 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Note : Because a dynamic W AN IP can change from time to time depending on your ISP , you may want to obtain a S tatic IP address from your ISP . A S tatic IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera f[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 96 Enter valid ports in the Vir t u al Server section of your router . Please make sure to check the box on this line to enable settings. Then the device can be access from W AN by the router ’s W AN IP Address. By now , you have finished your entire PC configuration for this device. App[...]

5. Appendix 9 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual z Ethernet Network Environment Normally , DDNS service is only necessary for t he users that could only obtain dynamic IP addresses. As to the users that could obtain the st atic valid IP address, they do not usually have to apply the DDNS service. Before we deci de if DDNS is necessar[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 98 (3). After the columns show up at the lef t side, click “ Create Account ”. (4). Fill the application agreem ent and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d. Submit all the input informa tion and finish creating an account[...]

5. Appendix 9 9 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Click these two options (5). Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink a ddress to confirm the DDNS serv ice that you just applied. Then DDNS you applied activated. Click to confirm[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 100 (6). Enter the web page http://www .dyndns.org/ again. Input your username and password that you just applied to login admin istration interface of DDNS server . Input your account (7). If the correct username and password are input, you can see the following picture at the top-right o[...]

5. Appendix 1 0 1 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual (9). Click the “ Dynamic DNS ”. (10). Click the “ Get S tarted ”. (1 1). We could create a domain name without any c harge at this step. First, we input the host name. (Pink No.1) Then we pick a domai n that is easy to remember . (Pink No.2) The 3rd step is to click “Of fli[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 102 1 2 z Setup the DDNS and PPPoE of Networked Device At last, users have to enter the web p age of Networked Device and setup the necessary information of DDNS and PPPoE after the application of DDNS service. Please check the user manual to access the DDNS and PPPoE pages. After saving t[...]

5. Appendix 1 0 3 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual within tolerances and commonly found. Austria 230V 50 Hz Brazil 1 10/220V* 60 Hz *127V found in states of Bahia, Paran?(including Curitiba), Rio de Janeiro, S 緌 Paulo and Minas Gerais (though 220V may be found in some hotels). Other areas are 220V only , with the exception of Forta[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 104 Though nominal voltage has been officially changed to 230V , 240V is within tolerances and commonly found. United S tates of America 120V 60 Hz Appendix I: 3GPP T o use the 3GPP function, in addition to previous section, you might need more information or configuration to make this fun[...]

5. Appendix 1 0 5 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operati ng system of PC is running Windows XP . Go to St art > Settings . Click Control Panel Click Add or Remove Programs[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 106 Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details[...]

5. Appendix 1 0 7 AirLive PoE-2600HD/ WN-2600HD User ’ s Manual Select Universal Plug and Play Click Ok Click Next[...]

5. Appendix AirLive PoE-2600HD/ WN-2600HD User ’ s Manual 108 Please wait while Setup configures the components. Click Finish[...]