ACR Electronics 2844 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung ACR Electronics 2844 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von ACR Electronics 2844, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung ACR Electronics 2844 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung ACR Electronics 2844. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung ACR Electronics 2844 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts ACR Electronics 2844
- Den Namen des Produzenten und das Produktionsjahr des Geräts ACR Electronics 2844
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts ACR Electronics 2844
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von ACR Electronics 2844 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von ACR Electronics 2844 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service ACR Electronics finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von ACR Electronics 2844 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts ACR Electronics 2844, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von ACR Electronics 2844 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    OWNER VESSEL RAD IO CALL SIGN UIN #[...]

  • Seite 2

    Y1 - 03 - 0242 Rev. B 1 NOTE re: A pplicable prod ucts This manual supports all configurations of G lobalFix™ PRO/ RLB - 37 beacons . In addition to the part num bers listed on the cover page, o ther configurations of these products are available, thus you may have purchased a product configuration with a somewhat diff erent part number. As long [...]

  • Seite 3

    Y1 - 03 - 0242 Rev. B 2 Ta ble of Contents STEP ONE - REGISTERING YOUR BEAC ON ____________________________ 3 STEP TWO - HOW TH E BEACON W ORKS _____________________________ 6 STEP THREE - INSTALL ING THE BEAC ON _____________________________ 15 STEP FOUR - MAIN TAINING THE BEACON ___________________________ 19 APPENDIX A - USING AN D TESTING THE G[...]

  • Seite 4

    Y1 - 03 - 0242 Rev. B 3 STEP ONE - REGISTERING YOUR BEAC ON 1. Why is registration imp ortant? As the ow ner of this 406 MHz beacon, i t is mandatory that you registe r it with the EPIRB national autho rity o f your country : It is the law . Please note that a ll 406 MHz beac ons are required to have their registration updated every two years b y t[...]

  • Seite 5

    Y1 - 03 - 0242 Rev. B 4 2. What country should I register in? Register your beacon with the EPIR B national authority of the country for which th e beacon was programm ed, typically the countr y where purchased , regardless of where you do your boating. The beacon m ust be reprogramm ed if you, as the owner, move or the vessel sails under the flag [...]

  • Seite 6

    Y1 - 03 - 0242 Rev. B 5 Registration outside of the United States In countries other than the United States, 4 06 MHz beacons are register ed with that country’s national authorit y at the tim e of purchase. T he s ales agent should have ass isted y ou in f illing out the forms and sending them to the country’s n ational aut hority. Altern ativ[...]

  • Seite 7

    Y1 - 03 - 0242 Rev. B 6 STEP TWO - HOW THE BEACON WORKS 1. How your beacon brings help 406 MHz beacons are a t ype of port able emergenc y equipm ent that transm its a distress signal to s earch and rescue ( SAR) organizatio ns . T he purpose of these beacons is to aid SAR team s in tracking and locating ships or individuals in jeopard y as rapidly[...]

  • Seite 8

    Y1 - 03 - 0242 Rev. B 7 2. Anatomy of your b eacon NOTE : W hen unpacking your beacon, it is recommended that you save the original packaging f or re -use when sh ipping th e beacon for battery replacement in the f uture. // A ctivation switch w ith Witness Tab The activ ation s witch em bodies a special, patented method of activating a beacon . Re[...]

  • Seite 9

    Y1 - 03 - 0242 Rev. B 8 Internal GPS Receiver Activation/Test Switch Red LED OFF/READY Position TEST Position ON/TRANSM ITTING Position Top View Switch Positions Strobes Antenna Green LED[...]

  • Seite 10

    Y1 - 03 - 0242 Rev. B 9 Spring Release knob HydroFix™ Hydrostatic Release Unit (HRU) Front cover ho ok (detent) Release Latch Antenna hoo k Water Sensor Deactivation M agnet GPS Interface Stowage Port Category 2 – Low Pro ™ 3 Bracket Category 1 – Se aShelter ™ 3 Bracket Front Cover Release Tabs Ejector spring Antenna hook[...]

  • Seite 11

    Y1 - 03 - 0242 Rev. B 10 3. Activating your bea con Overview Category I beacons are designed to be a utomatically deplo yed and activated in the event of a sinking vessel. The beacon may also be hand held on the deck of vessels, or floated in water and at tached to a raft or life vest with the lanyard provided. Category II beacons are designed to b[...]

  • Seite 12

    Y1 - 03 - 0242 Rev. B 11 Category I beacons -Automatic deplo y ment and activation If the vessel sink s, the HydroFix™ H RU frees the beac on f rom the bracket, allowing it t o float to the surf ace. Buil t -in sensors detect that the be acon is no longer in its bracket and when contin uity is created b y wat er between t wo of the top cap screws[...]

  • Seite 13

    Y1 - 03 - 0242 Rev. B 12 Category I and II Be acons-Manual Activatio n W ithout Deployment The beacon can be manuall y ac tivated while still in its brac ket by placing the Activation Switch in the ON position. Act ivation by th is m ethod overrides all senso rs and turns the beacon “ON.” Category I and II Be acons-Manual de ploy ment and activ[...]

  • Seite 14

    Y1 - 03 - 0242 Rev. B 13 TIPS FOR OPT IMUM DEPLOYMENT O F AN ACTIV ATED BEACON: When activating and deploying your beacon in an emergency, DO NOT: // Hold or clutch the be acon or antenna // Operate the beacon while hand held, if at all poss ible // Turn the beacon off for any reason, includ ing to save power // Activate the beac on if you have any[...]

  • Seite 15

    Y1 - 03 - 0242 Rev. B 14 Precautions to prevent f alse alarm s // Do not m ount or transport the beaco n within 4.6ft/1 .4 m of a m agneti c source. // Do not store the beaco n outside of its brack et. // Do not m ount the E PIRB back wards in its brack et (lan y ard r oll mus t face in). // Do not clean the beacon with a water hose and brush while[...]

  • Seite 16

    Y1 - 03 - 0242 Rev. B 15 STEP THREE - INST A LLING THE BEACON 1. Marking batt ery and Hydrostatic Release Unit expiration dates NOTE : It is the beacon o wner’s responsi bility to record the expira tion dates for both the beacon b attery and the H ydroFix™ hydrostatic release u nit. This inform ation must a ppe ar on the product itself. The lef[...]

  • Seite 17

    Y1 - 03 - 0242 Rev. B 16 Visually inspect the area su rrounding the m ounting brack et installation site f or hidden hazards or obstac les th at m ay ha ve been overlook ed during the location selection. If there is any doubt as to the rea dy acces sibility to th e beacon at all tim es or if an y condition m ay appear to be questio nable, conduct a[...]

  • Seite 18

    Y1 - 03 - 0242 Rev. B 17 3. Category I bracket The SeaShelter 3 ™ Categor y I bracket has five pre -drilled screw h oles to use for s ecuring the brack et to a f lat surface. Rem ove the SeaShelter 3 ™ lid b y turning th e spring loaded k nob on the lid 1/4 turn counter clockwise and pull. The lid will lift away f rom the top of the base and di[...]

  • Seite 19

    Y1 - 03 - 0242 Rev. B 18 4. Category II bracket Category II brack ets are design ed to ho ld the beacon sec urely i n p lace. T he beacon m ust be m anually deplo yed. The bracket can be m ounted on a vertical flat surf ace with beacon a ntenna u p or on a horizontal flat s urface facing sk yward. This location m ust be easil y accessible in order [...]

  • Seite 20

    Y1 - 03 - 0242 Rev. B 19 STEP FOUR - MAINTA INING THE BE ACON 1. Safety DOs and DON’T s On a routine basis abo ard ship, DO NO T: // Hold or carr y the beacon b y its antenn a // Mount the beacon in its brack et close to large s tructures or m agnetic areas // Tie the lan y ard to the EPIR B bracket or an y other struc ture // Obscure the beaco n[...]

  • Seite 21

    Y1 - 03 - 0242 Rev. B 20 Always refer battery replacem ent and any other beacon service to a factor y authorized Service Center. Find a Center near y ou at http://www.acrelectron ics.com/brc.htm . B attery repl acement incl udes servicing t he b eacon b y re placing all o -rings, testing the water seal and the electrical properties an d doing a ful[...]

  • Seite 22

    Y1 - 03 - 0242 Rev. B 21 6. Changing ow nership or contact information As the owner of the beacon, it is your responsibi lity to advise the national authority of an y c hange i n the inform ation on the r egistration form . If you are transferring the beacon to a new owner, you are required to inf orm the national authorit y . You can do this by us[...]

  • Seite 23

    Y1 - 03 - 0242 Rev. B 22 To remove th e expired HRU W hen opening the SeaShe lter 3 ™ lid, note th at the beacon is installed with the lanyard face in. Pu ll the beacon with stea dy pressure from the brack et. Do not get beaco n wet wh ile out of brac ket. The HRU has a ke y ing feature tha t locks it to the bracket. If you view the HRU rod as th[...]

  • Seite 24

    Y1 - 03 - 0242 Rev. B 23 9. Servicing the Low Pro 3 ™ To r emove a beaco n from the Category II brack et, lift the latch an d r elease the press ure from the beacon. The beacon will now be able to slide upwards out of the brack et. It is not anticipated that the LowPro 3 ™ will require servicing other than cleaning or, rarel y , replacem ent. B[...]

  • Seite 25

    Y1 - 03 - 0242 Rev. B 24 11. Extended GPS test The beacon m ay be tested for GPS functiona lity, how ever, this ma y on ly be done once in the fi ve-year lifetime of the batter y due to the si gnificant drain on th e batter y . This test is not necessar y at an y time in the life of the beacon, but is made available in the event that the beacon o w[...]

  • Seite 26

    Y1 - 03 - 0242 Rev. B 25 A PPENDIX A - USING A ND TESTING THE GPS S YSTEMS 1. Internal GPS position system The GlobalFix™ PRO is fitted with an inter nal GPS receiver that will determine the coord inates (latitude and longitude) of the beacon’s positio n on the globe, to be transm itted to the Cosp as-Sarsat em ergency system. W hen the beacon [...]

  • Seite 27

    Y1 - 03 - 0242 Rev. B 26 A PPENDIX B - THE COSPA S-S A RSAT SYSTEM 1. General ove rview EPIRBs transmit t o the satellite portion of the Cospas-Sarsat system. Cospas-Sarast satellites are an internation al syst em that utilizes Russian Federa tion and United States’ low altitude, near-polar orbiting satellites (LEOSAR). These satellites assist i [...]

  • Seite 28

    Y1 - 03 - 0242 Rev. B 27 A PPENDIX C - TECHNICA L SPECIFIC A TIONS GENERAL / ENVIRONMENTAL Beacon size (without antenna) 17.7 H X 10 .67 W X 9.09 D cm (6.97 X 4.2 X 3.58 in) Beacon we ight 581 g (20 .49 oz) Beacon ma terial High impact UV resistan t polymer Color ACR- Treuse™ (high visibility yellow) Waterproof Tested to 10 min @10 m (33 ft), exc[...]

  • Seite 29

    Y1 - 03 - 0242 Rev. B 28 A PPENDIX D - WARRA NTY, USEFUL LIFE POLICY, NOTICES 1. Limited Warranty This product is warranted against factory defects in material a nd workmanship fo r a period of 1 (one) year* from date of purchase or receipt as a gift. During the warranty period ACR Electronics, Inc. will repair or, at its option, replace the unit a[...]

  • Seite 30

    Y1 - 03 - 0242 Rev. B 29 EC DECLARAT ION OF CONFORM ITY ACR Electronics hereby declares that the following product is in conformity with Council Directive 96/98/EC of 20 Decem ber 1996 on Marine Equipment (M ED) last ame nde d by Commission Directive 2009/26/EC of 6 April 20 09, and has be en type e x amined as described in this Decla ration. In a [...]

  • Seite 31

    Y1 - 03 - 0242 Rev. B 30 IN TER NA TIO NA L MA RI T I M E OR GA NI ZA TI ON SH OR E B A SE D MA IN T E NA NC E Th e Ma r i t i me Sa f e ty Co mmi tt e e a p p r o v ed gu i d e l in es fo r sh o r e- ba sed ma in te n a n ce ( SB M ) of sa te l l i te EP IR B s , fo r th e p u r p o se of es ta b l i s h i n g s ta nd a r d i z e d pr o c e d u r [...]